- 您現在的位置：買賣IC網 > PDF目錄361238 > Q67107-H5167-A703 (SIEMENS AG) DDC-PLUS-Deflection Controller PDF資料下載
參數資料
| 型號： | Q67107-H5167-A703 |
| 廠商： | SIEMENS AG |
| 英文描述： | DDC-PLUS-Deflection Controller |
| 中文描述： | DDC的加偏轉控制器 |
| 文件頁數： | 25/47頁 |
| 文件大?。?/td> | 237K |
| 代理商： | Q67107-H5167-A703 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
SDA 9361
Semiconductor Group
25
1998-02-01
Vertical Scan
(width0 and width1)
The total width of this control item is 10 Bit. Therefore two registers (width0 and width1)
are necessary. If enabled (STE = 1) it defines the duration of the vertical scan. When the
vertical period has more lines than the sum of
Start Vertical Scan
and
Vertical Scan
,
the calculation of the vertical saw-tooth, the east/west parabola and the vertical parabola
required for HD stops so that the corresponding output signals remain unchanged till the
next vertical synchron pulse.
Guard Band
This control item is useful for optimizing self adaptation. Video signals with different
number of lines in consecutive fields (e. g. VCR search mode) must not start the
procedure of self adaptation. But switching between different TV standards has to
change the slope of the vertical saw-tooth getting always the same amplitude (self
adaptation). To avoid problems with flicker free TV systems which have alternating
number of lines per field an average value of four consecutive fields is calculated. If the
deviation of these average values (e.g. PAL: 312.5 lines or 625 half lines) is less or
equals
Guard Band
, no adaptation takes place. When it exceeds
Guard Band
, the
vertical slope will be changed.
Start Reduced Scan
If enabled (SRSE = 1) this item defines the start of the D/A conversion of the calculated
vertical saw-tooth. From begin of the vertical flyback to the line defined by
Start
Reduced Scan
the output signals VD+, VD- remain unchanged (flyback level). Other
outputs are not affected.
a) control bits VR1, VR0 # 00 (reduction of vertical size)
In this case the byte is useful for e.g. displaying 16/9 source format on 4/3 picture
tubes without visible RGB lines generated of the automatic cut-off control (partial
overscan). It defines the start of the reduced amplitude (factors 0.5, 0.66, 0.75) of the
vertical saw-tooth (
refer page 39
). When
Start Reduced Scan
= 0 the reduction
takes place over all lines including vertical flyback.
b) control bits VR1, VR0 = 00 (no reduction of vertical size)
If
Start Reduced Scan
>
Start Vertical Scan
the D/A conversion of the saw-tooth
starts (
Start Reduced Scan
-
Start Vertical Scan
) lines after begin of the
calculation. This causes a jump of the output voltage VD+, VD- from flyback to scan
level. It may be useful to hide the automatic cut-off control lines if no overscan is
desired (e.g. for VGA display). If
Start Reduced Scan
<=
Start Vertical Scan
this
byte has no effect.
相關PDF資料 |
PDF描述 |
|---|---|
| Q67120-C1056SAB-C501G-1EP | IC-8-BIT CPU |
| Q67120-C508 | IC-SM-8-BIT CPU 12-MHZ |
| Q67121C2168A1 | IC-SM-16 BIT CPU |
| Q67121C452 | IC-SM-8-BIT CPU-12MHZ |
| Q67126-C2088 | RF inductor, ceramic core, 2% tol, SMT, RoHS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Q67120-C0508 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Single-Chip Microcontroller |
| Q67120-C0509 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Single-Chip Microcontroller |
| Q67120-C0510 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Single-Chip Microcontroller |
| Q67120-C0562 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Single-Chip Microcontroller |
| Q67120-C0581 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Single-Chip Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。