- 您現在的位置：買賣IC網 > PDF目錄225025 > RC28F128P33T85 (NUMONYX) 8M X 16 FLASH 3V PROM, 85 ns, PBGA64 PDF資料下載
參數資料
| 型號： | RC28F128P33T85 |
| 廠商： | NUMONYX |
| 元件分類： | PROM |
| 英文描述： | 8M X 16 FLASH 3V PROM, 85 ns, PBGA64 |
| 封裝： | BGA-64 |
| 文件頁數： | 55/96頁 |
| 文件大?。?/td> | 1378K |
| 代理商： | RC28F128P33T85 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁當前第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
November 2007
Datasheet
Order Number: 314749-05
59
Numonyx StrataFlash Embedded Memory (P33)
available; if cleared, the buffer is not available. To retry, issue the Buffered
Programming Setup command again, and re-check SR[7]. When SR[7] is set, the
buffer is ready for loading. (see Figure 35, “Buffer Program Flowchart” on page 71).
On the next write, a word count is written to the device at the buffer address. This tells
the device how many data words will be written to the buffer, up to the maximum size
of the buffer.
On the next write, a device start address is given along with the first data to be written
to the flash memory array. Subsequent writes provide additional device addresses and
data. All data addresses must lie within the start address plus the word count.
Optimum programming performance and lower power usage are obtained by aligning
the starting address at the beginning of a 32-word boundary (A[4:0] = 0x00). Crossing
a 32-word boundary during programming will double the total programming time.
After the last data is written to the buffer, the Buffered Programming Confirm command
must be issued to the original block address. The WSM begins to program buffer
contents to the flash memory array. If a command other than the Buffered
Programming Confirm command is written to the device, a command sequence error
occurs and SR[7,5,4] are set. If an error occurs while writing to the array, the device
stops programming, and SR[7,4] are set, indicating a programming failure.
When Buffered Programming has completed, additional buffer writes can be initiated by
issuing another Buffered Programming Setup command and repeating the buffered
program sequence. Buffered programming may be performed with VPP = VPPL or VPPH
(see Section 5.2, “Operating Conditions” on page 26 for limitations when operating the
device with VPP = VPPH).
If an attempt is made to program past an erase-block boundary using the Buffered
Program command, the device aborts the operation. This generates a command
sequence error, and SR[5,4] are set.
If Buffered programming is attempted while VPP is below VPPLK, SR[4,3] are set. If any
errors are detected that have set Status Register bits, the Status Register should be
cleared using the Clear Status Register command.
11.3.3
Buffered Enhanced Factory Programming
Buffered Enhanced Factory Programing (BEFP) speeds up Multi-Level Cell (MLC) flash
programming. The enhanced programming algorithm used in BEFP eliminates
traditional programming elements that drive up overhead in device programmer
systems.
BEFP consists of three phases: Setup, Program/Verify, and Exit (see Figure 36, “BEFP
Flowchart” on page 72). It uses a write buffer to spread MLC program performance
across 32 data words. Verification occurs in the same phase as programming to
accurately program the flash memory cell to the correct bit state.
A single two-cycle command sequence programs the entire block of data. This
enhancement eliminates three write cycles per buffer: two commands and the word
count for each set of 32 data words. Host programmer bus cycles fill the device’s write
buffer followed by a status check. SR[0] indicates when data from the buffer has been
programmed into sequential flash memory array locations.
Following the buffer-to-flash array programming sequence, the Write State Machine
(WSM) increments internal addressing to automatically select the next 32-word array
boundary. This aspect of BEFP saves host programming equipment the address-bus
setup overhead.
相關PDF資料 |
PDF描述 |
|---|---|
| RC28F256P33T85A | 16M X 16 FLASH 3V PROM, 85 ns, PBGA64 |
| RC28F160C3TC90 | 1M X 16 FLASH 3V PROM, 90 ns, PBGA64 |
| RC28F160C3BD70 | 1M X 16 FLASH 3V PROM, 70 ns, PBGA64 |
| RC4194K | DUAL OUTPUT, ADJUSTABLE MIXED REGULATOR, MBFM9 |
| RM4194K | DUAL OUTPUT, ADJUSTABLE MIXED REGULATOR, MBFM9 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RC28F128P33T85A | 功能描述:IC FLASH 128MBIT 85NS 64EZBGA RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:StrataFlash™ 標準包裝:2,500 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（單線） 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) |
| RC28F128P33TF60 | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:Numonyx?? P33-65nm Flash Memory |
| RC28F128P33TF60A | 功能描述:IC FLASH 128MBIT 85NS 64EZBGA RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:StrataFlash™ 標準包裝:72 系列:- 格式 - 存儲器:RAM 存儲器類型:SRAM - 同步 存儲容量:4.5M（256K x 18） 速度:133MHz 接口:并聯 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 封裝/外殼:100-LQFP 供應商設備封裝:100-TQFP（14x20） 包裝:托盤 |
| RC28F128P3GB850 | 制造商:Micron Technology Inc 功能描述:128MB, KEARNY EBGA 3.0 - Trays |
| RC28F128P3GT850 | 制造商:Micron Technology Inc 功能描述:128MB, KEARNY EBGA 3.0 - Trays |
發布緊急采購，3分鐘左右您將得到回復。