參數資料
型號: RC28F128P33T85
廠商: NUMONYX
元件分類: PROM
英文描述: 8M X 16 FLASH 3V PROM, 85 ns, PBGA64
封裝: BGA-64
文件頁數: 62/96頁
文件大?。?/td> 1378K
代理商: RC28F128P33T85
November 2007
Datasheet
Order Number: 314749-05
65
Numonyx StrataFlash Embedded Memory (P33)
11.4.6.4
Block Lock Status
The Read Device Identifier command is used to determine a block’s lock status (see
addressed block’s lock status; DQ0 is the addressed block’s lock bit, while DQ1 is the
addressed block’s lock-down bit.
11.4.6.5
Block Locking During Suspend
Block lock and unlock changes can be performed during an erase suspend. To change
block locking during an erase operation, first issue the Erase Suspend command.
Monitor the Status Register until SR[7] and SR[6] are set, indicating the device is
suspended and ready to accept another command.
Next, write the desired lock command sequence to a block, which changes the lock
state of that block. After completing block lock or unlock operations, resume the erase
operation using the Erase Resume command.
Note:
A Lock Block Setup command followed by any command other than Lock Block, Unlock
Block, or Lock-Down Block produces a command sequence error and set Status
Register bits SR[4] and SR[5]. If a command sequence error occurs during an erase
suspend, SR[4] and SR[5] remains set, even after the erase operation is resumed.
Unless the Status Register is cleared using the Clear Status Register command before
resuming the erase operation, possible erase errors may be masked by the command
sequence error.
If a block is locked or locked-down during an erase suspend of the same block, the lock
status bits change immediately. However, the erase operation completes when it is
resumed. Block lock operations cannot occur during a program suspend. See Appendix
, “Write State Machine” on page 87, which shows valid commands during an erase
suspend.
Figure 31: Block Locking State Diagram
[X00]
[X01]
Power-Up/Reset
Unlocked
Locked
[011]
[111]
[110]
Locked-
Down4,5
Software
Locked
[011]
Hardware
Locked5
Unlocked
WP# Hardware Control
Notes:
1. [a,b,c] represents [WP#, DQ1, DQ0]. X = Don’t Care.
2. DQ1 indicates Block Lock-Down status. DQ1 = ‘0’, Lock-Down has not been issued
to this block. DQ1 = ‘1’, Lock-Down has been issued to this block.
3. DQ0 indicates block lock status. DQ0 = ‘0’, block is unlocked. DQ0 = ‘1’, block is
locked.
4. Locked-down = Hardware + Software locked.
5. [011] states should be tracked by system software to determine difference between
Hardware Locked and Locked-Down states.
Software Block Lock (0x60/0x01) or Software Block Unlock (0x60/0xD0)
Software Block Lock-Down (0x60/0x2F)
WP# hardware control
相關PDF資料
PDF描述
RC28F256P33T85A 16M X 16 FLASH 3V PROM, 85 ns, PBGA64
RC28F160C3TC90 1M X 16 FLASH 3V PROM, 90 ns, PBGA64
RC28F160C3BD70 1M X 16 FLASH 3V PROM, 70 ns, PBGA64
RC4194K DUAL OUTPUT, ADJUSTABLE MIXED REGULATOR, MBFM9
RM4194K DUAL OUTPUT, ADJUSTABLE MIXED REGULATOR, MBFM9
相關代理商/技術參數
參數描述
RC28F128P33T85A 功能描述:IC FLASH 128MBIT 85NS 64EZBGA RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:StrataFlash™ 標準包裝:2,500 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?(單線) 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP,8-MSOP(0.118",3.00mm 寬) 供應商設備封裝:8-MSOP 包裝:帶卷 (TR)
RC28F128P33TF60 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:Numonyx?? P33-65nm Flash Memory
RC28F128P33TF60A 功能描述:IC FLASH 128MBIT 85NS 64EZBGA RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:StrataFlash™ 標準包裝:72 系列:- 格式 - 存儲器:RAM 存儲器類型:SRAM - 同步 存儲容量:4.5M(256K x 18) 速度:133MHz 接口:并聯(lián) 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 封裝/外殼:100-LQFP 供應商設備封裝:100-TQFP(14x20) 包裝:托盤
RC28F128P3GB850 制造商:Micron Technology Inc 功能描述:128MB, KEARNY EBGA 3.0 - Trays
RC28F128P3GT850 制造商:Micron Technology Inc 功能描述:128MB, KEARNY EBGA 3.0 - Trays