- 您現在的位置：買賣IC網 > PDF目錄16499 > SI5315-EVB (Silicon Laboratories Inc)BOARD EVAL SI5315 8KHZ-644.53MHZ PDF資料下載
參數資料
| 型號： | SI5315-EVB |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 25/54頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL SI5315 8KHZ-644.53MHZ |
| 應用說明： | SI5315/17 Crystal Selection AppNote |
| 標準包裝： | 1 |
| 主要目的： | 計時，時鐘乘法器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | SI5315 |
| 主要屬性： | 2 輸入，2 輸出 |
| 次要屬性： | CML，CMOS，LVDS，LVPECL |
| 已供物品： | 板，CD，文檔 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
Si5315
Rev. 1.0
31
The prioritization of clock inputs for automatic switching is shown in Table 14. This priority is hardwired in the
devices.
At power-on or reset, the valid CKINn with the highest priority (1 being the highest priority) is automatically
selected. If no valid CKINn is available, the device suppresses the output clocks and waits for a valid CKINn signal.
If the currently selected CKINn goes into an alarm state, the next valid CKINn in priority order is selected. If no valid
CKINn is available, the device enters holdover.
Operation in revertive and non- revertive is different when a signal becomes valid:
Revertive (AUTOSEL = H):
The device constantly monitors all CKINn. If a CKINn with a higher priority than
the current active CKINn becomes valid, the active CKINn is changed to the
CKINn with the highest priority.
Non-revertive (AUTOSEL = M): The active clock does not change until there is an alarm on the active clock. The
device will then select the highest priority CKINn that is valid. Once in holdover,
the device will switch to the first CKINn that becomes valid.
5.4. Alarms
Summary alarms are available to indicate the overall status of the input signals. Alarm outputs stay high until all the
alarm conditions for that alarm output are cleared.
5.4.1. Loss-of-Signal
The device has loss-of-signal circuitry that continuously monitors CKINn for missing pulses. The LOS circuitry
generates an internal LOSn_INT output signal that is processed with other alarms to generate LOS1 and LOS2.
An LOS condition on CKIN1 causes the internal LOS1_INT alarm to become active. Similarly, an LOS condition on
CKINn causes the LOSn_INT alarm to become active. Once a LOSn_INT alarm is asserted on one of the input
clocks, it remains asserted until that input clock is validated over a designated time period. The time to clear
LOSn_INT after a valid input clock appears is listed in Table 3, “AC Characteristics”. If another error condition on
the same input clock is detected during the validation time then the alarm remains asserted and the validation time
starts over.
5.4.1.1. LOS Algorithm
The LOS circuitry divides down each input clock to produce an 8 kHz to 2 MHz signal. The LOS circuitry over
samples this divided down input clock using a 40 MHz clock to search for extended periods of time without input
clock transitions. If the LOS monitor detects twice the normal number of samples without a clock edge, a
LOSn_INT alarm is declared. Table 3, “AC Characteristics” gives the minimum and maximum amount of time for
the LOS monitor to trigger.
5.4.1.2. Lock Detect
The PLL lock detection algorithm indicates the lock status on the LOL output pin. The algorithm works by
continuously monitoring the phase of the input clock in relation to the phase of the feedback clock. If the time
between two consecutive phase cycle slips is greater than the retrigger time, the PLL is in lock. The LOL output
has a guaranteed minimum pulse width as shown in (Table 3, “AC Characteristics”). The LOL pin is also held in the
active state during an internal PLL calibration. The retrigger time is automatically set based on the PLL closed loop
bandwidth (See Table 15).
Table 14. Input Clock Priority for Auto Switching
Priority
Input Clocks
1CKIN1
2CKIN2
3
Holdover
相關PDF資料 |
PDF描述 |
|---|---|
| CB5016-000 | HEAT SHRINK TUBING |
| ESC08DRTN-S93 | CONN EDGECARD 16POS DIP .100 SLD |
| ESC13DRYH-S13 | CONN EDGECARD 26POS .100 EXTEND |
| ESC05DRES-S734 | CONN EDGECARD 10POS .100 EYELET |
| VE-24L-EX | CONVERTER MOD DC/DC 28V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI5315-H | 制造商:KODENSHI 制造商全稱:KODENSHI KOREA CORP. 功能描述:Colorless transparency lens type |
| SI5315-H(B) | 制造商:AUK 制造商全稱:AUK corp 功能描述:IRED |
| SI5315-H_1 | 制造商:AUK 制造商全稱:AUK corp 功能描述:IRED |
| SI5315-HB | 制造商:AUK 制造商全稱:AUK corp 功能描述:IRED |
| SI5316 | 制造商:SILABS 制造商全稱:SILABS 功能描述:PRELIMINARY DATA SHEET PRECISION CLOCK JITTER ATTENUATOR |
發布緊急采購，3分鐘左右您將得到回復。