- 您現在的位置：買賣IC網 > PDF目錄373785 > ZL50015QCC (ZARLINK SEMICONDUCTOR INC) Enhanced 1 K Digital Switch with Stratum 4E DPLL PDF資料下載
參數資料
| 型號： | ZL50015QCC |
| 廠商： | ZARLINK SEMICONDUCTOR INC |
| 元件分類： | 路由/交換 |
| 英文描述： | Enhanced 1 K Digital Switch with Stratum 4E DPLL |
| 中文描述： | TELECOM, DIGITAL TIME SWITCH, PQFP256 |
| 封裝： | 28 X 28 MM, 1.40 MM HEIGHT, MS-026BJC, LQFP-256 |
| 文件頁數： | 46/122頁 |
| 文件大小： | 926K |
| 代理商： | ZL50015QCC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
ZL50015
Data Sheet
46
Zarlink Semiconductor Inc.
16.0 Microprocessor Port
The device provides access to the internal registers, connection memories and data memories via the
microprocessor port. The microprocessor port is capable of supporting both Motorola and Intel non-multiplexed
microprocessors. The microprocessor port consists of a 16-bit parallel data bus (D15 - 0), 14 bit address bus (A13 -
0) and six control signals (MOT_INTEL, CS, DS_RD, R/W_WR, IRQ and DTA_RDY).
The data memory can only be read from the microprocessor port. For a data memory read operation, D7 - 0 will be
used and D15 - 8 will output zeros.
For a CM_L read or write operation, all bits (D15 - 0) of the data bus will be used. For a CM_H write operation, D4 -
0 of the data bus must be configured and D15 - 5 are ignored. D15 - 5 must be driven either high or low. For a
CM_H read operation, D4 - 0 will be used and D15 - 5 will output zeros.
Refer to Figure 26 on page 94, Figure 27 on page 95, Figure 28 on page 96 and Figure 29 on page 97 for the
microprocessor timing.
17.0 Device Reset and Initialization
The RESET pin is used to reset the ZL50015. When this pin is low, the following functions are performed:
synchronously puts the microprocessor port in a reset state
tristates the STio0 - 15 outputs
drives the STOHZ0 - 7 outputs to high
preloads all internal registers with their default values (refer to the individual registers for default values)
clears all internal counters
17.1 Power-up Sequence
The recommended power-up sequence is for the V
DD_IO
supply (normally +3.3 V) to be established before the
power-up of the V
DD_CORE
supply (normally +1.8 V). The V
DD_CORE
supply may be powered up at the same time
as V
DD_IO
, but should not “l(fā)ead” the V
DD_IO
supply by more than 0.3 V.
17.2 Device Initialization on Reset
Upon power up, the ZL50015 should be initialized as follows:
Set the ODE pin to low to disable the STio0 - 15 outputs and to drive STOHZ0 - 7 to high
Set the TRST pin to low to disable the JTAG TAP controller
Reset the device by pulsing the RESET pin to zero for longer than 1
μ
s
After releasing the RESET pin from low to high, wait for a certain period of time (see Note below) for the
device to stabilize from the power down state before the first microprocessor port access can occur
Program CKIN1 - 0 (bit 6 -5) in the Control Register (CR) to define the frequency of the CKi and FPi inputs
Wait at least 500
μ
s prior to the next microport access (see Note below)
Use the block programming mode to initialize the connection memory
Note
: If an external oscillator is used, the waiting time is 500
μ
s. Without the external oscillator, if CKi is
16.384 MHz, the waiting time is 500
μ
s; if CKi is 8.192 MHz, the waiting time is 1 ms; if CKi is 4.096 MHz, the
waiting time is 2 ms.
Release the ODE pin from low to high after the connection memory is programmed
相關PDF資料 |
PDF描述 |
|---|---|
| ZL50015QCC1 | Enhanced 1 K Digital Switch with Stratum 4E DPLL |
| ZL50018 | 2 K Digital Switch with Enhanced Stratum 3 DPLL |
| ZL50018GAC | 2 K Digital Switch with Enhanced Stratum 3 DPLL |
| ZL50018QCC | 2 K Digital Switch with Enhanced Stratum 3 DPLL |
| ZL50019 | Enhanced 2 K Digital Switch with Stratum 4E DPLL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ZL50015QCC1 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Enhanced 1 K Digital Switch with Stratum 4E DPLL |
| ZL50015QCG1 | 制造商:Microsemi Corporation 功能描述: 制造商:Microsemi Corporation 功能描述:PB FREE 1K+RATE CONVERSION AND S4E DPLL 制造商:Microsemi Corporation 功能描述:PB FREE 1K+RATE CONVERSION AND S4E DPLL - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TDM SWITCH 1K-CH ENH 256LQFP 制造商:Microsemi Corporation 功能描述:IC TDM SWITCH 1K-CH ENH 256LQFP |
| ZL50016 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Enhanced 1 K Digital Switch |
| ZL50016_06 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Enhanced 1 K Digital Switch |
| ZL50016GAC | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 1K X 1K 1.8V/3.3V 256BGA - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TDM SWITCH 1K-CH ENH 256PBGA 制造商:Microsemi Corporation 功能描述:IC TDM SWITCH 1K-CH ENH 256PBGA |
發布緊急采購，3分鐘左右您將得到回復。