- 您現在的位置：買賣IC網 > PDF目錄382783 > μPD29F008AL-X (NEC Corp.) 8 M-Bit CMOS Low Voltage Flash Memory(8M CMOS低壓閃存) PDF資料下載
參數資料
| 型號： | μPD29F008AL-X |
| 廠商： | NEC Corp. |
| 英文描述： | 8 M-Bit CMOS Low Voltage Flash Memory(8M CMOS低壓閃存) |
| 中文描述： | 8 m位的CMOS低電壓快閃記憶體（800萬的CMOS低壓閃存） |
| 文件頁數： | 11/44頁 |
| 文件大?。?/td> | 249K |
| 代理商： | ΜPD29F008AL-X |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Preliminary Data Sheet
11
μ
PD29F008AL-X
3.5 Hardware Reset
The device can be reset to read mode by maintaining the /RESET pin at V
IL
at least during the t
RP
period.
While the /RESET pin is held at V
IL
, all write and read commands are ignored. Moreover, all output pins go into high
impedance. At this time, the supply current can be kept at 5
μ
A or below by maintaining /RESET at GND
±
0.2 V.
When performing reset, the operations in progress are all interrupted. Therefore, when reset is performed during
program or erase (including erase suspend), the address or sector data become undefined. In this case, after reset is
completed, perform the program or erase operation again.
3.6 Sector Protect
The sector protect function enables protection of any sector. Protected sectors cannot be programmed or erased,
and any combination of up to 19 sectors can be protected.
To select the sector protect mode, apply V
ID
to A9 and /OE. Moreover, input V
IL
, V
IH
, and V
IL
to A0, A1, and A6,
respectively, input the sector address of the sector to be protected to A13 to A19, and input V
IL
to /CE.
Sector protection starts at the falling edge of the /WE pulse and ends at the rising edge of the same pulse. Maintain
the sector address at a constant level during the /WE pulse interval.
To perform sector protect verification, apply V
ID
to A9. Also input V
IL
, V
IH
, and V
IL
to A0, A1, and A6, respectively,
and the sector address of the sector to be verified to A13 to A19. The other address pins are Don't Care (V
IL
is
recommended.)
When read from the input sector address is performed, the sector protect verification result is output to I/O0. If the
verified sector is protected, "1" is output to I/O0. If it is not protected, "0" is output.
Sector protect enables writing commands by applying V
ID
to /RESET. Moreover, it is also possible to unprotect the
sector with the same method. For details, see section
4.9 Sector Protect (by Command Input)
, and section
4.10
Sector Unprotect
.
Figure 3-1. Sector Protect Timing Chart
Note
The sector protect verification result is output.
01H : The sector is protected.
00H : The sector is not protected.
SAx
A13 - A19 (Input)
A0 (Input)
A1 (Input)
A6 (Input)
A9 (Input)
/OE (Input)
/WE (Input)
/CE (Input)
I/O (Output)
t
VLHT
t
VLHT
t
CSP
t
OESP
t
WPP
t
VLHT
t
VLHT
t
OE
SAy
01H
Note
V
ID
V
IH
V
ID
V
IH
(Sector protect)
(Verify sector protect)
相關PDF資料 |
PDF描述 |
|---|---|
| μPD29F008L | 8 M-Bit CMOS 3.0 V-Only Flash Memory(8M CMOS 3V工作電壓的閃存) |
| μPD30100 | 64-bit RISC Microprosessor(64位 RISC 微處理器) |
| μPD30101 | 64-Bit Microprocessor(64位微處理器) |
| μPD30102 | 64-/32-BIT Microprocessor(64/32位微處理器) |
| μPD30121 | 64-Bit MIPS RISC Microprocessor(64 位RISC 微處理器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PD2M | 制造商:ANADIGICS 制造商全稱:ANADIGICS, Inc 功能描述:2mm InGaAs Photodiode |
| PD2M-0XX | 制造商:ANADIGICS 制造商全稱:ANADIGICS, Inc 功能描述:2mm InGaAs Photodiode |
| PD2M-1XX | 制造商:ANADIGICS 制造商全稱:ANADIGICS, Inc 功能描述:2mm InGaAs Photodiode |
| PD2-O4118L1804 | 制造商:NANOTEC 功能描述:MOTOR PLUG & DRIVE 42MM 0.5NM 制造商:NANOTEC 功能描述:MOTOR, PLUG & DRIVE, 42MM, 0.5NM |
| PD2-O4118S1404 | 制造商:NANOTEC 功能描述:MOTOR PLUG & DRIVE 42MM 0.3NM 制造商:NANOTEC 功能描述:MOTOR, PLUG & DRIVE, 42MM, 0.3NM 制造商:NANOTEC 功能描述:MOTOR, PLUG & DRIVE, 42MM, 0.3NM; Torque Max:0.2N-m; Current Rating:1.4A; No. of Phases:Two; SVHC:No SVHC (19-Dec-2012); External Height:42.3mm; Supply Voltage Max:24V; Supply Voltage Min:12V ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。