- 您現在的位置：買賣IC網 > PDF目錄382783 > μPD29F008AL-X (NEC Corp.) 8 M-Bit CMOS Low Voltage Flash Memory(8M CMOS低壓閃存) PDF資料下載
參數資料
| 型號： | μPD29F008AL-X |
| 廠商： | NEC Corp. |
| 英文描述： | 8 M-Bit CMOS Low Voltage Flash Memory(8M CMOS低壓閃存) |
| 中文描述： | 8 m位的CMOS低電壓快閃記憶體（800萬的CMOS低壓閃存） |
| 文件頁數： | 15/44頁 |
| 文件大?。?/td> | 249K |
| 代理商： | ΜPD29F008AL-X |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Preliminary Data Sheet
15
μ
PD29F008AL-X
4.2 Read / Reset
This command resets the device to the read mode.
When the device is in the read mode, no command is necessary for reading data. Data read can be performed
using the read cycle of a standard microprocessor.
The read mode is maintained until the contents of the command register are changed.
4.3 Read Product ID code
This command is used to read the manufacturer code or the device code of the device.
The manufacturer code (10H) is output by inputting 00000H in the address using the fourth write cycle. The device
code is output when 00001H is input.
The manufacturer code and device code can be read by selecting the read product ID code mode by applying V
ID
to
the A9 pin (See section
3.8 Read Product ID Code
). However, applying a high voltage to the address pin is not
desirable due to system design considerations. Using this command allows reading the manufacturer code and
device code without applying a high voltage to the pin.
4.4 Program
This command is used to program data.
Program is performed in 1-byte units. Program can be performed regardless of the address sequence, even if the
sector limit is exceeded. However, "0" cannot be changed back into "1" through the program operation. If overwriting
"1" to "0" is attempted, the program operation is interrupted and "1" is output to I/O5, or successful program is
indicated in data polling, but actually the data is "0" as before.
Following write by command sequence, the pulse required for program is automatically generated inside the device
and program verification is automatically performed, so that control from external is not required.
During automatic program, all commands that have been written are ignored. However, automatic program is
interrupted when hardware reset is performed. Since the programmed data is not guaranteed in this case, reexecute
the program command following completion of reset.
Upon completion of automatic program, the device returns to the read mode.
The operation status of automatic program can be determined by using the hardware sequence flags (I/O7, I/O6, RY
(/BY) pins).
See sections
5.1 I/O7 (Data Polling)
,
5.2 I/O6 (Toggle Bit)
, and
5.6 RY (/BY) (Ready / Busy)
.
Figure 4-1. Program Flow Chart
Start
Write program
command sequence
I/O7 = Data
Yes
No
Data poll from system
Increment address
Yes
No
Last address
Programing
completed
相關PDF資料 |
PDF描述 |
|---|---|
| μPD29F008L | 8 M-Bit CMOS 3.0 V-Only Flash Memory(8M CMOS 3V工作電壓的閃存) |
| μPD30100 | 64-bit RISC Microprosessor(64位 RISC 微處理器) |
| μPD30101 | 64-Bit Microprocessor(64位微處理器) |
| μPD30102 | 64-/32-BIT Microprocessor(64/32位微處理器) |
| μPD30121 | 64-Bit MIPS RISC Microprocessor(64 位RISC 微處理器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PD2M | 制造商:ANADIGICS 制造商全稱:ANADIGICS, Inc 功能描述:2mm InGaAs Photodiode |
| PD2M-0XX | 制造商:ANADIGICS 制造商全稱:ANADIGICS, Inc 功能描述:2mm InGaAs Photodiode |
| PD2M-1XX | 制造商:ANADIGICS 制造商全稱:ANADIGICS, Inc 功能描述:2mm InGaAs Photodiode |
| PD2-O4118L1804 | 制造商:NANOTEC 功能描述:MOTOR PLUG & DRIVE 42MM 0.5NM 制造商:NANOTEC 功能描述:MOTOR, PLUG & DRIVE, 42MM, 0.5NM |
| PD2-O4118S1404 | 制造商:NANOTEC 功能描述:MOTOR PLUG & DRIVE 42MM 0.3NM 制造商:NANOTEC 功能描述:MOTOR, PLUG & DRIVE, 42MM, 0.3NM 制造商:NANOTEC 功能描述:MOTOR, PLUG & DRIVE, 42MM, 0.3NM; Torque Max:0.2N-m; Current Rating:1.4A; No. of Phases:Two; SVHC:No SVHC (19-Dec-2012); External Height:42.3mm; Supply Voltage Max:24V; Supply Voltage Min:12V ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。