參數資料
型號: 37C669
廠商: SMSC Corporation
英文描述: DIODE SCHOTTKY SINGLE 25V 200mW 0.5V-vf 200mA-IFM 30mA-IF 2uA-IR SOD-323 3K/REEL
中文描述: 電腦98/99順從超級I / O軟盤控制器與紅外線支持
文件頁數: 4/164頁
文件大?。?/td> 621K
代理商: 37C669
101
requests from the Parallel Port to the CPU due
to a low to high transition on the nACK input.
Refer to the description of the interrupt under
Operation, Interrupts.
BIT 5 DIRECTION
If mode=000 or mode=010, this bit has no effect
and the direction is always out regardless of the
state of this bit. In all other modes, Direction is
valid and a logic 0 means that the printer port is
in output mode (write); a logic 1 means that the
printer port is in input mode (read).
Bits 6 and 7 during a read are a low level, and
cannot be written.
cFifo (Parallel Port Data FIFO)
ADDRESS OFFSET = 400h
Mode = 010
Bytes written or DMAed from the system to this
FIFO are transmitted by a hardware handshake
to the peripheral using the standard parallel port
protocol.
Transfers to the FIFO are byte
aligned.
This mode is only defined for the
forward direction.
ecpDFifo (ECP Data FIFO)
ADDRESS OFFSET = 400H
Mode = 011
Bytes written or DMAed from the system to this
FIFO, when the direction bit is 0, are transmitted
by a hardware handshake to the peripheral
using the ECP parallel port protocol. Transfers
to the FIFO are byte aligned.
Data bytes from the peripheral are read under
automatic hardware handshake from ECP into
this FIFO when the direction bit is 1. Reads or
DMAs from the FIFO will return bytes of ECP
data to the system.
tFifo (Test FIFO Mode)
ADDRESS OFFSET = 400H
Mode = 110
Data bytes may be read, written or DMAed to or
from the system to this FIFO in any direction.
Data in the tFIFO will not be transmitted to the
to the parallel port lines using a hardware
protocol handshake.
However, data in the
tFIFO may be displayed on the parallel port data
lines.
The tFIFO will not stall when overwritten or
underrun. If an attempt is made to write data to
a full tFIFO, the new data is not accepted into
the tFIFO. If an attempt is made to read data
from an empty tFIFO, the last data byte is re-
read again.
The full and empty bits must
always keep track of the correct FIFO state. The
tFIFO will transfer data at the maximum ISA
rate so that software may generate performance
metrics.
The FIFO size and interrupt threshold can be
determined by writing bytes to the FIFO and
checking the full and serviceIntr bits.
The writeIntrThreshold can be determined by
starting with a full tFIFO, setting the direction bit
to 0 and emptying it a byte at a time until
serviceIntr is set.
This may generate a
spurious interrupt, but will indicate that the
threshold has been reached.
The readIntrThreshold can be determined by
setting the direction bit to 1 and filling the empty
tFIFO a byte at a time until serviceIntr is set.
This may generate a spurious interrupt, but will
indicate that the threshold has been reached.
相關PDF資料
PDF描述
37C672 ENHANCED SUPER I/O CONTROLLER WITH FAST IR
37C67X ENHANCED SUPER I/O CONTROLLER WITH FAST IR
37C957FR ULTRA I/O CONTROLLER FOR PORTABLE APPLICATIONS
37FMA1-ABW31N SPECIAL SWITCH-PIEZO SWITCH, SPST, MOMENTARY, 0.2A, 24VDC, PANEL MOUNT-THREADED
37FML1-BEW31N SPECIAL SWITCH-PIEZO SWITCH, SPST, MOMENTARY, 0.2A, 24VDC, PANEL MOUNT-THREADED
相關代理商/技術參數
參數描述
37C672 制造商:SMSC 制造商全稱:SMSC 功能描述:ENHANCED SUPER I/O CONTROLLER WITH FAST IR
37C67X 制造商:SMSC 制造商全稱:SMSC 功能描述:ENHANCED SUPER I/O CONTROLLER WITH FAST IR
37C-6BH-5-5 制造商:Birtcher Products 功能描述:
37C72U-185 制造商:White-Rodgers 功能描述:
37C73U-170 制造商:White-Rodgers 功能描述: