參數資料
型號: 37C669
廠商: SMSC Corporation
英文描述: DIODE SCHOTTKY SINGLE 25V 200mW 0.5V-vf 200mA-IFM 30mA-IF 2uA-IR SOD-323 3K/REEL
中文描述: 電腦98/99順從超級I / O軟盤控制器與紅外線支持
文件頁數: 9/164頁
文件大?。?/td> 621K
代理商: 37C669
106
are always possible with standard or PS/2 mode
using program control of the control signals.
Interrupts
The interrupts are enabled by serviceIntr in the
ecr register.
serviceIntr = 1
Disables the DMA and all of
the service interrupts.
serviceIntr = 0
Enables the selected interrupt
condition.
If the interrupting
condition is valid, then the
interrupt
is
generated
immediately when this bit is
changed from a 1 to a 0. This
can occur during Programmed
I/O if the number of bytes
removed or added from/to the
FIFO
does
not
cross
the
threshold.
The interrupt generated is ISA friendly in that it
must pulse the interrupt line low, allowing for
interrupt
sharing.
After
a
brief
pulse
low
following the interrupt event, the interrupt line is
tri-stated so that other interrupts may assert.
An interrupt is generated when:
1. For DMA transfers: When serviceIntr is 0,
dmaEn is 1 and the DMA TC is received.
2. For Programmed I/O:
a.
When serviceIntr is 0, dmaEn is 0,
direction
is
0
and
there
are
writeIntrThreshold or more free bytes in
the
FIFO.
Also,
an
interrupt
is
generated when serviceIntr is cleared
to
0
whenever
there
are
writeIntrThreshold or more free bytes in
the FIFO.
b.
(1)
When serviceIntr is 0, dmaEn
is 0, direction is 1 and there
are readIntrThreshold or more
bytes in the FIFO.
Also, an
interrupt is generated when
serviceIntr is cleared to 0
whenever
there
are
readIntrThreshold
or
more
bytes in the FIFO.
3. When nErrIntrEn is 0 and nFault transitions
from high to low or when nErrIntrEn is set
from 1 to 0 and nFault is asserted.
4. When ackIntEn is 1 and the nAck signal
transitions from a low to a high.
FIFO Operation
The
FIFO
threshold
is
set
in
the
chip
configuration registers. All data transfers to or
from the parallel port can proceed in DMA or
Programmed I/O (non-DMA) mode as indicated
by the selected mode.
The FIFO is used by
selecting the Parallel Port FIFO mode or ECP
Parallel Port Mode. (FIFO test mode will be
addressed separately). After a reset, the FIFO
is disabled. Each data byte is transferred by a
Programmed I/O cycle or PDRQ depending on
the selection of DMA or Programmed I/O mode.
The following paragraphs detail the operation of
the FIFO flow control.
In these descriptions,
<threshold>
ranges
from
1
to
16.
The
parameter FIFOTHR, which the user programs,
is one less and ranges from 0 to 15.
A low threshold value (i.e. 2) results in longer
periods of time between service requests, but
requires faster servicing of the request for both
read and write cases.
The host must be very
responsive to the service request.
This is the
desired case for use with a "fast" system.
相關PDF資料
PDF描述
37C672 ENHANCED SUPER I/O CONTROLLER WITH FAST IR
37C67X ENHANCED SUPER I/O CONTROLLER WITH FAST IR
37C957FR ULTRA I/O CONTROLLER FOR PORTABLE APPLICATIONS
37FMA1-ABW31N SPECIAL SWITCH-PIEZO SWITCH, SPST, MOMENTARY, 0.2A, 24VDC, PANEL MOUNT-THREADED
37FML1-BEW31N SPECIAL SWITCH-PIEZO SWITCH, SPST, MOMENTARY, 0.2A, 24VDC, PANEL MOUNT-THREADED
相關代理商/技術參數
參數描述
37C672 制造商:SMSC 制造商全稱:SMSC 功能描述:ENHANCED SUPER I/O CONTROLLER WITH FAST IR
37C67X 制造商:SMSC 制造商全稱:SMSC 功能描述:ENHANCED SUPER I/O CONTROLLER WITH FAST IR
37C-6BH-5-5 制造商:Birtcher Products 功能描述:
37C72U-185 制造商:White-Rodgers 功能描述:
37C73U-170 制造商:White-Rodgers 功能描述: