參數資料
型號： 82845Mx
廠商： Intel Corp.
英文描述： Intel 845 Family Chipset-Mobile 82845MP/82845MZ Chipset Memory Controller Hub Mobile (MCH-M)
中文描述： 英特爾845系列芯片組的手機82845MP/82845MZ芯片組內存控制器中樞移動（婦幼保健米）
文件頁數： 119/157頁
文件大小： 1407K
代理商： 82845MX
Intel
82845MP/82845MZ Chipset-Mobile (MCH-M)
250687-002
Datasheet
119
R
MCH-M Host Bridge
AGP
Command
C/BE[3:0]#
Encoding
Cycle Destination
Response as PCIx Target
Reserved
1111
N/A
No Response
NOTE:
N/A refers to a function that is not applicable.
As a target of an AGP cycle, the MCH-M supports all memory read and write transactions targeted at
main memory (summarized in the table above). The MCH-M supports both normal and high priority read
and write requests. The MCH-M does not support AGP cycles to the hub interface. PIPE# and SBA
cycles do not require coherency management and all AGP initiator accesses to main memory using AGP
PIPE# or SBA protocol are treated as non-snoopable cycles. These accesses are directed to the AGP
aperture in main memory that should be programmed as either uncacheable (UC) memory or write
combining (WC) in the processor’s MTRRs.
5.3.2.
AGP Transaction Ordering
The MCH-M observes transaction ordering rules as defined by the
AGP Interface Specification Rev 2.0
.
5.3.3.
AGP Signal Levels
The 1x/2x/4x data transfers use 1.5-V signaling levels as described in the AGP 2.0 specification.
5.3.4.
4x AGP Protocol
In addition to the 1x and 2x AGP protocol, the MCH-M supports 4x AGP read and write data transfers
and 4x sideband address. The 4x operation is compliant with the AGP 2.0 specification.
The MCH-M indicates that it supports 4x data transfers through RATE[2] (bit 2) of the AGP Status
Register. When DATA_RATE[2] of the AGP Command Register is set to 1 during system initialization,
the MCH-M performs AGP read/write data transactions using 4x protocol. This bit is not dynamic. Once
this bit is set during initialization, the data transfer rate may not be changed.
The 4x data rate transfer provides 1.06 GB/s transfer rates. The control signal protocol for the 4x data
transfer protocol is identical to 1x/2x protocol. In 4x mode 16 bytes of data are transferred on every 66-
MHz clock edge. The minimum throttleable block size remains four 66-MHz clocks, which means 64
bytes of data are transferred per block. Three additional signal pins are required to implement the 4x data
transfer protocol. These signal pins are complementary data transfer strobes for the AD bus (2) and the
SBA bus (1).
5.3.5.
Fast Writes
MCH-M supports 2x and 4x Fast Writes from the MCH-M to the graphics controller on AGP. Fast Write
operation is compliant with the AGP 2.0 specification.
The MCH-M will not generate Fast Back to Back (FB2B) cycles in 1x mode, but will generate FB2B
cycles in 2x and 4x Fast Write modes.
To use the Fast Write protocol, the Fast Write Enable configuration bit, AGPCMD[FWEN] (bit 4 of the
AGP Command Register), must be set to 1.
相關PDF資料
PDF描述
82845MZ Intel 845 Family Chipset-Mobile 82845MP/82845MZ Chipset Memory Controller Hub Mobile (MCH-M)
82845PE 82845GE Graphics and Memory Controller Hub (GMCH) and 82845PE Memory Controller Hub (MCH)
82845GE 82845GE Graphics and Memory Controller Hub (GMCH) and 82845PE Memory Controller Hub (MCH)
8284A Clock Generator and Driver for 8066, 8088 Processors
8284A-1 Clock Generator and Driver for 8066, 8088 Processors
相關代理商/技術參數
參數描述
82845MZ 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel 845 Family Chipset-Mobile 82845MP/82845MZ Chipset Memory Controller Hub Mobile (MCH-M)
82845PE 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:82845GE Graphics and Memory Controller Hub (GMCH) and 82845PE Memory Controller Hub (MCH)
8284611SM 制造商:Thomas & Betts 功能描述:
828461-2 制造商:TE Connectivity 功能描述:19P CPC STECK-GEH - Bulk
828462-1 制造商:TE Connectivity 功能描述:19P CPC AUFNAHMEGEH - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*