參數資料
型號: AD6636BC
廠商: Analog Devices, Inc.
元件分類: 數字上/下變頻
英文描述: 150 MSPS Wideband Digital Down-Converter (DDC)
中文描述: 150MSPS的寬帶數字下變頻器(DDC)
文件頁數: 64/72頁
文件大?。?/td> 1629K
代理商: AD6636BC
AD6636
MRCF Control Register <12:0>
<12:10>: MRCF Data Select Bits. These bits are used to select
the input source for the MRCF filter. Each MRCF filter can be
driven by output from the HB2 filter of any channel independ-
ently. Table 36 shows the selections available.
Rev. 0 | Page 64 of 72
Table 36. MRCF Data Select Bits
MRCF Data Select<2:0>
000
001
010
011
1x0
1x1
MRCF Input Source
MRCF input taken from Channel 0
MRCF input taken from Channel 1
MRCF input taken from Channel 2
MRCF input taken from Channel 3
MRCF input taken from Channel 4
MRCF input taken from Channel 5
<9>: Interpolating Half-Band Enable Bit. When this bit is set,
the interpolating half-band filter, driven by the output of the
CRCF block, is enabled. When cleared, the interpolating half-
band filter is bypassed and its output is the same as its input.
The interpolating half-band filter doubles the data rate.
<8>: This bit is open.
<7>: Half-Rate Bit. When this bit is set, the MRCF filter operates
using half the PLL clock rate. This is used for power savings
when there is sufficient time to complete MRCF filtering using
only half the PLL clock rate. When this bit is cleared, the MRCF
filter operates at the full PLL clock rate. (See the Mono-Rate
RAM Coefficient Filter section.)
<6:4>: MRCF Number of Taps Bits. This 3-bit word should be
written with one less than the number of taps that are calculated
by the MRCF filter. The filter length is given by the decimal
value of this register plus 1. A value of 0 represents a 1-tap filter
and maximum value of 7 represents an 8-tap filter.
<3:2>: MRCF Scale Factor Bits. The output of the MRCF filter is
scaled according to the value of these bits. Table 37 describes
the attenuation corresponding to each setting.
Table 37. MRCF Scale Factor
MRCF Scale<1:0>
00
01
10
11
Scale Factor
18.06 dB attenuation (left-shift 3 bits)
12.04 dB attenuation (left-shift 2 bits)
6.02 dB attenuation (left-shift 1 bit)
No Scaling (0 dB)
<1>: This bit is open.
<0>: MRCF Bypass Bit. When this bit is set, the MRCF filter is
bypassed and, therefore, the output of the MRCF is the same as
its input. When this bit is cleared, the MRCF has normal
operation as programmed by its control register.
MRCF Coefficient Memory
The MRCF coefficient memory consists of eight coefficients,
each six bits wide. The memory extends from Address 0x80 to
Address 0x87. The coefficients should be written in twos
complement format.
DRCF Control Register <11:0>
<11>: DRCF Bypass Bit. When this bit is set, the DRCF filter is
bypassed and, therefore, its output is the same as its input. When
this bit is cleared, the DRCF has normal operation as pro-
grammed by the rest of this control register.
<10>: Symmetry Bit. When this bit is set, it indicates that the
DRCF is implementing a symmetrical filter and only half the
impulse response needs to be written into the DRCF coefficient
RAM. When this bit is cleared, the filter is asymmetrical and
complete impulse response of the filter should be written to the
coefficient RAM. When this filter is symmetrical, it can
implement up to 128 filter taps.
<9:8>: DRCF Multiply Accumulate Scale Bits.The output of the
DRCF filter is scaled according to the value of these bits.
Table 38 lists the attenuation corresponding to each setting.
Table 38. DRCF Multiply Accumulate Scale Bits
DRCF Scale<1:0>
Scale Factor
00
18.06 dB attenuation (left-shift 3 bits)
01
12.04 dB attenuation (left-shift 2 bits)
10
6.02 dB attenuation (left-shift 1 bit)
11
No Scaling (0 dB)
<7:4>: DRCF Decimation Rate. This 4-bit word should be
written with one less than the decimation rate of the DRCF
filter. A value of 0 represents a decimation rate of 1 (no rate
change), and the maximum value of 15 represents a decimation
of 16. Filtering can be implemented irrespective of the
decimation rate.
<3:0>: DRCF Decimation Phase Bits. This 4-bit word represents
the decimation phase used by the DRCF filter. The valid range is
0 up to M
DRCF
1, where M
DRCF
is the decimation rate of the
DRCF filter. This word is primarily used for synchronization of
multiple channels of the AD6636, when more than one channel
is used for filtering one signal (one carrier).
DRCF Coefficient Offset <7:0>
This register is used to specify which section of the 64-word
coefficient memory is used for a filter. It can be used to select
between multiple filters that are loaded into memory and
referenced by this pointer. This register is shadowed, and the
filter pointer is updated every time a new filter is started. This
allows the coefficient offset to be written even while a filter is
being computed without disturbing operation. The next sample
comes out of the DRCF with the new filter.
相關PDF資料
PDF描述
AD6636CBCZ1 150 MSPS Wideband Digital Down-Converter (DDC)
AD6636PCB 150 MSPS Wideband Digital Down-Converter (DDC)
AD664(中文) Monolithic 12-Bit Quad DAC(單片12位四D/A轉換器)
AD6640 12-Bit, 65 MSPS IF Sampling A/D Converter
AD6640AST 12-Bit, 65 MSPS IF Sampling A/D Converter
相關代理商/技術參數
參數描述
AD6636BC/PCB 制造商:Analog Devices 功能描述:Evaluation Board For 150MSPS Wideband Digital Down-Converter 制造商:Analog Devices 功能描述:EVALUATION BOARD AD6636 - Bulk
AD6636BC/PCBZ 制造商:Analog Devices 功能描述:Evaluation Kit For 150 MSPS, Wide Band, Digital Down Converter 制造商:Analog Devices 功能描述:EVALUATION BOARD AD6636 - Bulk
AD6636CBC 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
AD6636CBCZ 功能描述:IC DIGITAL DWNCONV 4CH 256CSPBGA RoHS:是 類別:RF/IF 和 RFID >> RF 混頻器 系列:AD6636 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:100 系列:- RF 型:W-CDMA 頻率:2.11GHz ~ 2.17GHz 混頻器數目:1 增益:17dB 噪音數據:2.2dB 次要屬性:- 電流 - 電源:11.7mA 電源電壓:2.7 V ~ 3.3 V 包裝:托盤 封裝/外殼:12-VFQFN 裸露焊盤 供應商設備封裝:12-QFN-EP(3x3)
AD6636CBCZ1 制造商:AD 制造商全稱:Analog Devices 功能描述:150 MSPS Wideband Digital Down-Converter (DDC)