- 您現在的位置：買賣IC網 > PDF目錄16533 > AD9517-2A/PCBZ (Analog Devices Inc)BOARD EVALUATION FOR AD9517-2A PDF資料下載
參數資料
| 型號： | AD9517-2A/PCBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 21/80頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD9517-2A |
| 設計資源： | AD9517 Eval Brd Schematics AD9517 Gerber Files AD9517-2 BOM |
| 標準包裝： | 1 |
| 主要目的： | 計時，時鐘發生器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD9517-2A |
| 主要屬性： | 2 輸入，12 輸出，2.2GHz VCO |
| 次要屬性： | CMOS，LVPECL 和 LVDS 兼容 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
AD9517-2
Data Sheet
Rev. E | Page 28 of 80
THEORY OF OPERATION
OPERATIONAL CONFIGURATIONS
The AD9517 can be configured in several ways. These
configurations must be set up by loading the control registers
function must be individually programmed by setting the
appropriate bits in the corresponding control register or registers.
High Frequency Clock Distribution—CLK or External
VCO > 1600 MHz
The AD9517 power-up default configuration has the PLL
powered off and the routing of the input set so that the
CLK/CLK input is connected to the distribution section
through the VCO divider (divide-by-2/divide-by-3/divide-by-4/
divide-by-5/divide-by-6). This is a distribution only mode that
allows for an external input up to 2400 MHz (see Table 3). The
maximum frequency that can be applied to the channel dividers
is 1600 MHz; therefore, higher input frequencies must be divided
down before reaching the channel dividers. This input routing
can also be used for lower input frequencies, but the minimum
divide is 2 before the channel dividers.
When the PLL is enabled, this routing also allows the use of the
PLL with an external VCO or VCXO with a frequency of less
than 2400 MHz. In this configuration, the internal VCO is not
used and is powered off. The external VCO/VCXO feeds
directly into the prescaler.
The register settings shown in Table 21 are the default values of
these registers at power-up or after a reset operation. If the
contents of the registers are altered by prior programming after
power-up or reset, these registers can also be set intentionally to
these values.
After the appropriate register values are programmed,
Register 0x232 must be set to 0x01 for the values to take effect.
Table 21. Default Settings of Some PLL Registers
Register
Function
0x010[1:0] = 01b
PLL asynchronous power-down (PLL off).
0x1E0[2:0] = 010b
Set VCO divider = 4.
0x1E1[0] = 0b
Use the VCO divider.
0x1E1[1] = 0b
CLK selected as the source.
When using the internal PLL with an external VCO, the PLL
must be turned on.
Table 22. Settings When Using an External VCO
Register
Function
0x010[1:0] = 00b
PLL normal operation (PLL on).
0x010 to 0x01D
PLL settings. Select and enable a reference
input; set R, N (P, A, B), PFD polarity, and ICP,
according to the intended loop configuration.
0x1E1[1] = 0b
CLK selected as the source.
An external VCO requires an external loop filter that must be
connected between CP and the tuning pin of the VCO. This
loop filter determines the loop bandwidth and stability of the
PLL. Make sure to select the proper PFD polarity for the VCO
being used.
Table 23. Setting the PFD Polarity
Register
Function
0x010[7] = 0b
PFD polarity positive (higher control voltage
produces higher frequency).
0x010[7] = 1b
PFD polarity negative (higher control
voltage produces lower frequency).
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J00-EZ-S | CONVERTER MOD DC/DC 5V 25W |
| ILC0402ER15NK | INDUCTOR CER 15NH 0402 |
| SP1210R-473K | INDUCTOR PWR SHIELDED 47.0UH SMD |
| MCP121T-300E/TT | IC SUPERVISOR 2.93V LOW SOT-23B |
| AD9517-4A/PCBZ | BOARD EVALUATION FOR AD9517-4A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9517-2BCPZ | 制造商:Analog Devices 功能描述:Clock Generator 48-Pin LFCSP EP Tray |
| AD9517-2BCPZ-REEL7 | 制造商:Analog Devices 功能描述: |
| AD9517-2BCPZ-TR | 制造商:Analog Devices 功能描述:OUPUT CLOCK GENERATOR WITH 2.2HZ VCO - Tape and Reel |
| AD9517-3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Output Clock Generator with Integrated 2.0 GHz VCO |
| AD9517-3A/PCBZ | 功能描述:BOARD EVALUATION FOR AD9517-3A RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
發布緊急采購，3分鐘左右您將得到回復。