- 您現在的位置：買賣IC網 > PDF目錄16533 > AD9517-2A/PCBZ (Analog Devices Inc)BOARD EVALUATION FOR AD9517-2A PDF資料下載
參數資料
| 型號： | AD9517-2A/PCBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 62/80頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD9517-2A |
| 設計資源： | AD9517 Eval Brd Schematics AD9517 Gerber Files AD9517-2 BOM |
| 標準包裝： | 1 |
| 主要目的： | 計時，時鐘發生器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD9517-2A |
| 主要屬性： | 2 輸入，12 輸出，2.2GHz VCO |
| 次要屬性： | CMOS，LVPECL 和 LVDS 兼容 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁當前第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
Data Sheet
AD9517-2
Rev. E | Page 65 of 80
Reg.
Addr.
(Hex)
Bits
Name
Description
0x01C
[4:3]
Reserved
Reserved (default: 00b).
2
REF2 power-on
This bit turns the REF2 power on.
0: REF2 power off (default).
1: REF2 power on.
1
REF1 power-on
This bit turns the REF1 power on.
0: REF1 power off (default).
1: REF1 power on.
0
Differential
reference
Selects the PLL reference mode, differential or single-ended. Single-ended must be selected for the automatic
switchover between REF1 and REF2 to work.
0: single-ended reference mode (default).
1: differential reference mode.
0x01D
4
PLL status
Disables the PLL status register readback.
register disable
0: PLL status register enable (default).
1: PLL status register disable.
3
LD pin comparator
enable
Enables the LD pin voltage comparator. This function is used with the LD pin current source lock detect mode. When
in the internal (automatic) holdover mode, this function enables the use of the voltage on the LD pin to determine if
the PLL was previously in a locked state (see Figure 53). Otherwise, this function can be used with the REFMON and
STATUS pins to monitor the voltage on this pin.
0: disables LD pin comparator; internal/automatic holdover controller treats this pin as true (high) (default).
1: enables LD pin comparator.
2
Holdover enable
Along with Bit 0, enables the holdover function. Automatic holdover must be disabled during VCO calibration.
0: holdover disabled (default).
1: holdover enabled.
1
External
Enables the external hold control through the SYNC pin. (This disables the internal holdover mode.)
holdover control
0: automatic holdover mode—holdover controlled by automatic holdover circuit. (default)
1: external holdover mode—holdover controlled by SYNC pin.
0
Holdover enable
Along with Bit 2, enables the holdover function. Automatic holdover must be disabled during VCO calibration.
0: holdover disabled (default).
1: holdover enabled.
0x01F
6
VCO cal finished
Read-only register: indicates status of the VCO calibration.
0: VCO calibration not finished.
1: VCO calibration finished.
5
Holdover active
Read-only register: indicates if the part is in the holdover state (see Figure 53). This is not the same as holdover enabled.
0: not in holdover.
1: holdover state active.
4
REF2 selected
Read-only register: indicates which PLL reference is selected as the input to the PLL.
0: REF1 selected (or differential reference if in differential mode).
1: REF2 selected.
3
VCO frequency >
threshold
Read-only register: indicates if the VCO frequency is greater than the threshold (see Table 16: REF1, REF2, and VCO
frequency status monitor).
0: VCO frequency is less than the threshold.
1: VCO frequency is greater than the threshold.
2
REF2 frequency >
threshold
Read-only register: indicates if the frequency of the signal at REF2 is greater than the threshold frequency set by
Register 0x1A, Bit 6.
0: REF2 frequency is less than threshold frequency.
1: REF2 frequency is greater than threshold frequency.
1
REF1 frequency >
threshold
Read-only register: indicates if the frequency of the signal at REF2 is greater than the threshold frequency
set by Register 0x01A, Bit 6.
0: REF1 frequency is less than threshold frequency.
1: REF1 frequency is greater than threshold frequency.
0
Digital lock detect
Read-only register: digital lock detect.
0: PLL is not locked.
1: PLL is locked.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J00-EZ-S | CONVERTER MOD DC/DC 5V 25W |
| ILC0402ER15NK | INDUCTOR CER 15NH 0402 |
| SP1210R-473K | INDUCTOR PWR SHIELDED 47.0UH SMD |
| MCP121T-300E/TT | IC SUPERVISOR 2.93V LOW SOT-23B |
| AD9517-4A/PCBZ | BOARD EVALUATION FOR AD9517-4A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9517-2BCPZ | 制造商:Analog Devices 功能描述:Clock Generator 48-Pin LFCSP EP Tray |
| AD9517-2BCPZ-REEL7 | 制造商:Analog Devices 功能描述: |
| AD9517-2BCPZ-TR | 制造商:Analog Devices 功能描述:OUPUT CLOCK GENERATOR WITH 2.2HZ VCO - Tape and Reel |
| AD9517-3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Output Clock Generator with Integrated 2.0 GHz VCO |
| AD9517-3A/PCBZ | 功能描述:BOARD EVALUATION FOR AD9517-3A RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
發布緊急采購，3分鐘左右您將得到回復。