參數資料
型號： AD9547/PCBZ
廠商： Analog Devices Inc
文件頁數： 101/104頁
文件大?。?/td> 0K
描述： BOARD EVALUATION FOR AD9547
設計資源： AD9547 Schematic
AD9574 BOM
標準包裝： 1
主要目的： 計時，時鐘發生器
嵌入式： 否
已用 IC / 零件： AD9547
主要屬性： 2 個差分式或 4 個單端輸入
次要屬性： CMOS，LVPECL 和 LVDS 兼容
已供物品： 板
AD9547
Data Sheet
Rev. E | Page 96 of 104
Table 146. Save
Address
Bit
Bit Name
Description
0x0E02
[7:1]
Unused
Unused.
0
Save to EEPROM
Upload data to the EEPROM based on in the EEPROM storage sequence. This is an autoclearing bit.
When an EEPROM save/load transfer is complete, wait a minimum of 10 μs before starting the next
EEPROM save/load transfer.
Table 147. Load
Address
Bit
Bit Name
Description
0x0E03
[7:2]
Unused
Unused.
1
Loadfrom
EEPROM
Download data from the EEPROM. This is an autoclearing bit. Whenan EEPROM save/load transfer is
complete, wait a minimum of 10 μs before starting the next EEPROM save/load transfer.
0
Unused
Unused.
EEPROM STORAGE SEQUENCE (REGISTER 0x0E10 TO REGISTER 0x0E3F)
The default settings of Register 0x0E10 to Register 0x0E33 embody a sample scratch pad instruction sequence. The following is a description
of the register defaults under the assumption that the controller has been instructed to carry out an EEPROM storage sequence.
Table 148. EEPROM Storage Sequencefor System Clock Settings
Address
Bit
Bit Name
Description
0x0E10
[7:0]
System clock
The default value of this register is 0x08, which the controller interprets as a data instruction. Its
decimal value is 8, which tells the controller to transfer nine bytes of data (8 + 1) beginning at the
address specifiedby the next two bytes. The controller stores 0x08 in the EEPROM and increments
the EEPROM address pointer.
0x0E11
[7:0]
System clock
The default value of these two registers is 0x0100. Note that Register 0x0E11 and Register 0x0E12 are
the most significant and least significant bytes of the target address, respectively. Because the
previous register contains a data instruction, these two registers define a starting address (in this
case, 0x0100). The controller stores 0x0100 inthe EEPROM and incrementsthe EEPROM pointer by 2.
It then transfers nine bytes from the register map (beginning at Address 0x0100) to the EEPROM and
increments the EEPROM address pointer by 10 (nine data bytes and one checksum byte). The nine
bytes transferred correspond to the system clock parameters inthe register map.
0x0E12
[7:0]
0x0E13
[7:0]
I/O update
The default value of this register is 0x80, which the controller interprets as an I/O update instruction.
The controller stores 0x80 in the EEPROM and increments the EEPROM address pointer.
Table 149. EEPROM Storage Sequencefor System Clock Calibration
Address
Bit
Bit Name
Description
0x0E14
[7:0]
SYSCLK calibrate
The default value of this register is 0xA0, which the controller interprets as a calibrate instruction.
The controller stores 0xA0 in the EEPROM and increments the EEPROM address pointer.
Table 150. EEPROM Storage Sequencefor General Configuration Settings
Address
Bit
Bit Name
Description
0x0E15
[7:0]
General
The default value of this register is 0x14, which the controller interprets as a data instruction. Its
decimal value is 20, which tells the controller to transfer 21 bytes of data (20 + 1) beginning at the
address specifiedby the next two bytes. The controller stores 0x14 in the EEPROM and increments
the EEPROM address pointer.
0x0E16
[7:0]
General
The default value of these two registers is 0x0200. Note that Register
0x0E16 and Register 0x0E17 are
the most significant and least significant bytes of the target address, respectively. Because the
previous register contains a data instruction, these two registers define a startingaddress (inthis case,
0x0200). The controller stores 0x0200inthe EEPROM and increments the EEPROM pointer by 2. It then
transfers 21 bytes from the register map (beginning at Address 0x0200) to the EEPROM and incre-
ments the EEPROM address pointer by 22 (21 data bytes and one checksum byte). The 21 bytes
transferred correspond to the general configuration parameters inthe register map.
0x0E17
[7:0]
相關PDF資料
PDF描述
UPA1E331MPD1TD CAP ALUM 330UF 25V 20% RADIAL
LB2518T331M INDUCTOR WOUND 330UH 30MA 1007
VI-J0T-EZ-S CONVERTER MOD DC/DC 6.5V 25W
AD9540/PCBZ BOARD EVAL CLK GEN SYNTH 48LFCSP
HCM15DSEH-S243 CONN EDGECARD 30POS .156 EYELET
相關代理商/技術參數
參數描述
AD9548 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad/Octal Input Network Clock Generator/Synchronizer
AD9548/PCBZ 功能描述:BOARD EVAL FOR AD9548 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源
AD9548/PCBZ 制造商:Analog Devices 功能描述:Clock Generator Evaluation Board
AD9548BCPZ 功能描述:IC CLOCK GEN/SYNCHRONIZR 88LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1 系列:- 類型:時鐘/頻率發生器，多路復用器 PLL:是 主要目的:存儲器，RDRAM 輸入:晶體 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:1:2 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:Digi-Reel® 其它名稱:296-6719-6
AD9548BCPZ-REEL7 功能描述:IC CLOCK GEN/SYNCHRONIZR 88LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*