- 您現在的位置：買賣IC網 > PDF目錄16183 > AMIS49587GEVK (ON Semiconductor)KIT EVALUATION AMIS49587 PDF資料下載
參數資料
| 型號： | AMIS49587GEVK |
| 廠商： | ON Semiconductor |
| 文件頁數： | 2/55頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT EVALUATION AMIS49587 |
| 標準包裝： | 1 |
| 主要目的： | 接口，電源線路收發器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AMIS49587 |
| 已供物品： | 2 個板，線纜，CD，文檔 |
| 其它名稱： | AMIS49587GEVKOS |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
AMIS49587
http://onsemi.com
10
CRC
CRC is a 5V compliant open drain output. An external pullup resistor defines the logic high level as illustrated in Figure 5.
A typical value for this pullup resistance “R” is 10 k
W. The signal on this output depends on the cyclic redundancy code result
of the received frame. If the cyclic redundancy code is correct CRC = 1 during the pause between 2 time slots.
RESB
RESB is a digital input pin. It is used to perform a hardware reset of the AMIS49587. This pin supports a 5 V voltage level.
The reset is active when the signal is low (0 V).
TEST
TEST is a digital input pin. It is used to enable the test mode of the chip. Normal mode is activated when TEST signal is low
(0 V). For normal operation, the TEST pin may be left unconnected. Due to the internal pulldown, the signal is maintained to
low (0 V). TEST pin is not 5 V safe.
TX_ENB
TX_ENB is a digital output pin. It is low when the transmitter is activated. The signal is available to turn on the line driver.
TX_ENB is a 5 V safe with open drain output, hence a pullup resistance is necessary achieve the requested voltage level
associated with a logical one. See also Figure 5 for reference.
TX_OUT
TX_OUT is the analog output pin of the transmitter. The provided signal is the SFSK modulated frames. A filtering operation
must be performed to reduce the second order harmonic distortion. For this purpose an active filter is realized. Figure 7 gives
the representation of this filter.
Figure 7. TX_OUT Filter
ALC
control
ALC_IN
Transmitter (SFSK Modulator)
ARM
Interface
&
Control
TX_OUT
LP
Filter
TX_EN
TO TX POWER
OUTPUT STAGE
FROM LINE
DRIVER
C1
R1
VSSA
C2
R2
R3
C3
C4
ALC_IN
ALC_IN is the automatic level control analog input pin. The signal is used to adjust the level of the transmitted signal. The
signal level adaptation is based on the AC component. The DC level on the ALC_IN pin is fixed internally to 1.65 V. Comparing
the peak voltage of the AC signal with two internal thresholds does the adaptation of the gain. Low threshold is fixed to 0.4 V.
A value under this threshold will result in an increase of the gain. The high threshold is fixed to 0.6 V. A value over this threshold
will result in a decrease of the gain. A serial capacitance is used to block the DC components. The level adaptation is performed
during the transmission of the first two bits of a new frame. Eight successive adaptations are performed.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J51-EY-S | CONVERTER MOD DC/DC 12V 50W |
| 383LX473M025A062 | CAP ALUM 47000UF 25V 20% SNAP |
| M3DDK-3418R | IDC CABLE - MKR34K/MC34M/MKR34K |
| CMH322522-27NML | INDUCTOR WIREWOUND .027UH 1210 |
| VI-J50-EZ-F4 | CONVERTER MOD DC/DC 5V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMIS-50050 | 制造商:ON Semiconductor 功能描述:SPREAD SPECTRUM BASEBAND CNTRLR - Trays 制造商:ON Semiconductor 功能描述:SPREAD SPECTRUM BASEBAND CNTRLR - Tape and Reel |
| AMIS-50051 | 制造商:ON Semiconductor 功能描述:DMOD 32LQFP / - Trays 制造商:ON Semiconductor 功能描述:DMOD - Tape and Reel |
| AMIS-52000 | 制造商:AMI 制造商全稱:AMI 功能描述:Single-Chip Radio Transceiver |
| AMIS-52050 | 制造商:ON Semiconductor 功能描述:WIRELESS LOW POWER TRANSCEIVER - 433MHZ (300-700MHZ), SSOP - Rail/Tube 制造商:ON Semiconductor 功能描述:WIRELESS LOW POWER TRANSCEIVER - 433MHZ (300-700MHZ), SSOP - Tape and Reel |
| AMIS-52100 | 制造商:AMI 制造商全稱:AMI 功能描述:Transceiver with Clock and Data Recovery |
發布緊急采購，3分鐘左右您將得到回復。