參數資料
型號： COP8CBR9KMT8
廠商： National Semiconductor
文件頁數： 49/111頁
文件大?。?/td> 0K
描述： IC MCU EEPROM 8BIT 32K 56-TSSOP
標準包裝： 34
系列： COP8™ 8C
核心處理器： COP8
芯體尺寸： 8-位
速度： 20MHz
連通性： Microwire/Plus（SPI），UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 49
程序存儲器容量： 32KB（32K x 8）
程序存儲器類型： 閃存
RAM 容量： 1K x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
數據轉換器： A/D 16x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 56-TFSOP（0.240"，6.10mm 寬）
包裝： 管件
其它名稱： *COP8CBR9KMT8
SNOS535I – OCTOBER 2000 – REVISED MARCH 2013
Table 5-12. Typical Flash Memory Endurance
Low End of Operating Temp Range
Erase Time
40°C
20°C
0°C
25°C
>25°C
1 ms
60k
100k
2 ms
60k
100k
3 ms
60k
100k
4 ms
60k
100k
5 ms
70k
100k
6 ms
80k
100k
7 ms
90k
100k
8 ms
100k
5.11 Timers
The device contains a very versatile set of timers (T0, T1, T2 and T3). Timers T1, T2 and T3 and
associated autoreload/capture registers power up containing random data.
5.11.1 TIMER T0 (IDLE TIMER)
The device supports applications that require maintaining real time and low power with the IDLE mode.
This IDLE mode support is furnished by the IDLE Timer T0, which is a 16-bit timer. The user cannot read
or write to the IDLE Timer T0, which is a count down timer.
As described in Power Saving Features, the clock to the IDLE Timer depends on which mode the device
is in. If the device is in High Speed mode, the clock to the IDLE Timer is the instruction cycle clock (one-
fifth of the CKI frequency). If the device is in Dual Clock mode or Low Speed mode, the clock to the IDLE
Timer is the 32 kHz clock. For the remainder of this section, the term “selected clock” will refer to the clock
selected by the Power Save mode of the device. During Dual Clock and Low Speed modes, the divide by
10 that creates the instruction cycle clock is disabled, to minimize power consumption.
In addition to its time base function, the Timer T0 supports the following functions:
Exit out of the Idle Mode (See Idle Mode description)
WATCHDOG logic (See WATCHDOG description)
Start up delay out of the HALT mode
Start up delay from BOR
Figure 5-9 is a functional block diagram showing the structure of the IDLE Timer and its associated
interrupt logic.
Bits 11 through 15 of the ITMR register can be selected for triggering the IDLE Timer interrupt. Each time
the selected bit underflows (every 4k, 8k, 16k, 32k or 64k selected clocks), the IDLE Timer interrupt
pending bit T0PND is set, thus generating an interrupt (if enabled), and bit 6 of the Port G data register is
reset, thus causing an exit from the IDLE mode if the device is in that mode.
In order for an interrupt to be generated, the IDLE Timer interrupt enable bit T0EN must be set, and the
GIE (Global Interrupt Enable) bit must also be set. The T0PND flag and T0EN bit are bits 5 and 4 of the
ICNTRL register, respectively. The interrupt can be used for any purpose. Typically, it is used to perform a
task upon exit from the IDLE mode. For more information on the IDLE mode, refer to Power Saving
The Idle Timer period is selected by bits 0–2 of the ITMR register Bit 3 of the ITMR Register is reserved
and should not be used as a software flag. Bits 4 through 7 of the ITMR Register are used by the dual
clock and are described in Power Saving Features.
42
Functional Description
Copyright 2000–2013, Texas Instruments Incorporated
Product Folder Links: COP8CBR9 COP8CCR9 COP8CDR9
相關PDF資料
PDF描述
COP8CBR9HLQ8 IC MCU CMOS 8BIT 44LLP
MC9S08SH32VTJ MCU 8BIT 32K FLASH 20-TSSOP
MC9S08SH32VTG MCU 8BIT 32K FLASH 16-TSSOP
MC9S08SH16VWL MCU 8BIT 16K FLASH 28-SOIC
MC9S08SH16VTL MCU 8BIT 16K FLASH 28-TSSOP
相關代理商/技術參數
參數描述
COP8CBR9LVA8 功能描述:IC MCU EEPROM 8BIT 32K 68PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8C 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
COP8CCE9 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Microcontroller with 8k Memory, Virtual EEPROM, 10-Bit A/D and Brownout Reset
COP8CCE9HLQ7 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Microcontroller with 8k Memory, Virtual EEPROM, 10-Bit A/D and Brownout Reset
COP8CCE9HLQ9 功能描述:IC MCU FLASH 8BIT 8K A/D 44LLP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8C 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
COP8CCE9HVA7 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*