- 您現在的位置：買賣IC網 > PDF目錄1913 > DS1878T+T&R (Maxim Integrated Products)IC CTLR SFP W/DGTL LDD RX 28TQFN PDF資料下載
參數資料
| 型號： | DS1878T+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 26/101頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CTLR SFP W/DGTL LDD RX 28TQFN |
| 標準包裝： | 2,500 |
| 類型： | SFP+ 控制器 |
| 輸入類型： | 模擬，數字 |
| 輸出類型： | 數字 |
| 接口： | I²C，LDD，串行 |
| 電流 - 電源： | 2.5mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁
DS1878
SFP+ Controller with Digital LDD Interface
30
______________________________________________________________________________________
SCL
NOTE: TIMING IS REFERENCED TO VIL(MAX) AND VIH(MIN).
SDA
STOP
START
REPEATED
START
tBUF
tHD:STA
tHD:DAT
tSU:DAT
tSU:STO
tHD:STA
tSP
tSU:STA
tHIGH
tR
tF
tLOW
Figure 20. I2C Timing
I2C Communication
I2C Definitions
The following terminology is commonly used to
describe I2C data transfers.
Master device: The master device controls the
slave devices on the bus. The master device gen-
erates SCL clock pulses and START and STOP
conditions.
Slave devices: Slave devices send and receive
data at the master’s request.
Bus idle or not busy: Time between STOP and
START conditions when both SDA and SCL are inac-
tive and in their logic-high states.
START condition: A START condition is generated
by the master to initiate a new data transfer with a
slave. Transitioning SDA from high to low while SCL
remains high generates a START condition. See
Figure 20 for applicable timing.
STOP condition: A STOP condition is generated by
the master to end a data transfer with a slave.
Transitioning SDA from low to high while SCL
remains high generates a STOP condition. See
Figure 20 for applicable timing.
Repeated START condition: The master can use a
repeated START condition at the end of one data
transfer to indicate that it will immediately initiate a
new data transfer following the current one.
Repeated STARTs are commonly used during read
operations to identify a specific memory address to
begin a data transfer. A repeated START condition
is issued identically to a normal START condition.
See Figure 20 for applicable timing.
Bit write: Transitions of SDA must occur during the
low state of SCL. The data on SDA must remain valid
and unchanged during the entire high pulse of SCL
plus the setup and hold time requirements
(Figure 20). Data is shifted into the device during the
rising edge of the SCL.
Bit read: At the end a write operation, the master
must release the SDA bus line for the proper amount
of setup time (Figure 20) before the next rising edge
of SCL during a bit read. The device shifts out each
bit of data on SDA at the falling edge of the previous
SCL pulse and the data bit is valid at the rising edge
of the current SCL pulse. Remember that the master
generates all SCL clock pulses, including when it is
reading bits from the slave.
Acknowledgement (ACK and NACK): An acknowl-
edgement (ACK) or not acknowledge (NACK) is
always the ninth bit transmitted during a byte trans-
fer. The device receiving data (the master during a
read or the slave during a write operation) performs
an ACK by transmitting a zero during the ninth bit. A
device performs a NACK by transmitting a one dur-
ing the 9th bit. Timing (Figure 20) for the ACK and
NACK is identical to all other bit writes. An ACK is
the acknowledgment that the device is properly
receiving data. A NACK is used to terminate a read
相關PDF資料 |
PDF描述 |
|---|---|
| DS1881Z-050+T&R | IC DGTL POT NV 2CH 45K 16-SOIC |
| DS1882Z-050+T&R | IC POT DIGIT DL LOG 50K 16SOIC |
| DS1884AT+T | IC SFP PON ONU CTRLR 24TQFN |
| DS2105Z+ | IC SCSI TERMINATOR 16-SOIC |
| DS2106S/T&R | IC TERMINATOR SCSI 28-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS-187PU | 制造商:Shinagawa Shoko 功能描述: |
| DS-187U | 制造商:Shinagawa Shoko 功能描述: |
| DS1880E-050 | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1880E-050/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL LOG POT + EQUALIZER T&R - Tape and Reel |
| DS1880E-050/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。