參數資料
型號： DS1878T+T&R
廠商： Maxim Integrated Products
文件頁數： 65/101頁
文件大?。?/td> 0K
描述： IC CTLR SFP W/DGTL LDD RX 28TQFN
標準包裝： 2,500
類型： SFP+ 控制器
輸入類型： 模擬，數字
輸出類型： 數字
接口： I²C，LDD，串行
電流 - 電源： 2.5mA
安裝類型： 表面貼裝
封裝/外殼： 28-WFQFN 裸露焊盤
供應商設備封裝： 28-TQFN-EP（5x5）
包裝： 帶卷 (TR)
DS1878
SFP+ Controller with Digital LDD Interface
66
______________________________________________________________________________________
Table 02h, Register 8Bh: CNFGC
FACTORY DEFAULT
00h
READ ACCESS
PW2 or (PW1 and RWTBL246) or (PW1 and RTBL246)
WRITE ACCESS
PW2 or (PW1 and RWTBL246)
MEMORY TYPE
Nonvolatile (SEE)
8Bh
XOVEREN
INVMON2
TXDM34
TXDFG
TXDFLT
TXDIO
RSSI_FC
RSSI_FF
BIT 7
BIT 0
BIT 7
XOVEREN: Enables RSSI conversion to use the XOVER (Table 02h, Register 90h–91h) value during
MON3 conversions.
0 = Uses hysteresis for linear RSSI measurements.
1 = XOVER value is enabled for nonlinear RSSI measurements.
BIT 6
INVMON2:
0 = MON2 is referenced to GND.
1 = MON2 is referenced to VCC.
BIT 5
TXDM34: Enables TXD to reset alarms and warnings associated to MON3 and MON4 during a TXD
event.
0 = TXD event has no effect on the MON3 and MON4 alarms, warnings, and quick trips.
1 = MON3 and MON4 alarms, warnings, and quick trips are reset during a TXD event.
BIT 4
TXDFG: See Figure 15.
0 = FETG, an internal signal, has no effect on TXDOUT.
1 = FETG is enabled and ORed with other possible signals to create TXDOUT.
BIT 3
TXDFLT: See Figure 15.
0 = TXF pin has no effect on TXDOUT.
1 = TXF pin is enabled and ORed with other possible signals to create TXDOUT.
BIT 2
TXDIO: See Figure 15.
0 = (Default) TXD input signal is enabled and ORed with other possible signals to create TXDOUT.
1 = TXD input signal has no effect on TXDOUT.
BITS 1:0
RSSI_FC and RSSI_FF: RSSI Force Coarse and RSSI Force Fine. Control bits for RSSI mode of
operation on the MON3 conversion.
00b = Normal RSSI mode of operation (default).
01b = The fine settings of scale and offset are used for MON3 conversions.
10b = The coarse settings of scale and offset are used for MON3 conversions.
11b = Normal RSSI mode of operation.
相關PDF資料
PDF描述
DS1881Z-050+T&R IC DGTL POT NV 2CH 45K 16-SOIC
DS1882Z-050+T&R IC POT DIGIT DL LOG 50K 16SOIC
DS1884AT+T IC SFP PON ONU CTRLR 24TQFN
DS2105Z+ IC SCSI TERMINATOR 16-SOIC
DS2106S/T&R IC TERMINATOR SCSI 28-SOIC
相關代理商/技術參數
參數描述
DS-187PU 制造商:Shinagawa Shoko 功能描述:
DS-187U 制造商:Shinagawa Shoko 功能描述:
DS1880E-050 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS1880E-050/T&R 制造商:Maxim Integrated Products 功能描述:DUAL LOG POT + EQUALIZER T&R - Tape and Reel
DS1880E-050/T&R 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*