參數資料
型號： DS21Q59DK
廠商： Maxim Integrated Products
文件頁數： 4/76頁
文件大?。?/td> 0K
描述： KIT DESIGN FOR DS21Q59
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
主要目的： 電信，調幀器和線路接口裝置（LIU）
已用 IC / 零件： DS21Q59
DS21Q59 Quad E1 Transceiver
12 of 76
4.1 Pin Function Descriptions
Table 4-C. System (Backplane) Interface Pins
NAME
TYPE
FUNCTION
TCLK
I
Transmit Clock. TCLK is a 2.048MHz primary clock that is used to clock data through the transmit
formatter.
TSER
I
Transmit Serial Data. Transmit NRZ serial data. TSER is sampled on the falling edge of TCLK when
IBO disabled. It is sampled on the falling edge of SYSCLK when the IBO function is enabled.
TSYNC
I/O
Transmit Sync. As an input, pulse at this pin establishes either frame or multiframe boundaries for the
transmitter. As an output, it can be programmed to output either a frame or multiframe pulse.
RSER
O
Receive Serial Data. RSER is the received NRZ serial data. RSER is updated on the rising edges of
RCLK when the receive elastic store is disabled. It is updated on the rising edges of SYSCLK when the
receive elastic store is enabled.
RSYNC
I/O
Receive Sync. An extracted pulse one RCLK wide is output at this pin that identifies either frame or
CAS/CRC4 multiframe boundaries. If the receive elastic store is enabled, this pin can be enabled to be
an input at which a frame-boundary pulse synchronous with SYSCLK is applied.
SYSCLK
I
System Clock. SYSCLK is a 2.048MHz clock used to clock data out of the receive elastic store. When
the IBO is enabled SYSCLK can be a 4.096MHz, 8.192MHz, or 16.384MHz clock.
OUTA
O
User-Selectable Output A. OUTA is a multifunction pin the host can program to output various alarms,
clocks, or data, or be used to control external circuitry.
OUTB
O
User-Selectable Output B. OUTB is a multifunction pin the host can program to output various alarms,
clocks, or data, or be used to control external circuitry.
Table 4-D. Alternate Jitter Attenuator
NAME
TYPE
FUNCTION
AJACKI
I
Alternate Jitter Attenuator Clock Input. AJACKI is clock input to the alternate jitter attenuator.
AJACKO
O
Alternate Jitter Attenuator Clock Output. AJACKO is clock output of the alternate jitter attenuator.
Table 4-E. Clock Synthesizer
NAME
TYPE
FUNCTION
4/8/16MCK
O
4.096MHz/8.192MHz/16.384MHz Clock Output. 4/8/16MCK is a 4.096MHz, 8.192MHz, or 16.384MHz
clock output that is referenced to one of the four recovered line clocks (RCLKs) or to an external
2.048MHz reference.
REFCLK
I/O
Reference Clock. REFCLK can be configured as an output to source a 2.048MHz reference clock or as
an input to supply a 2.048MHz reference clock from an external source to the clock synthesizer.
Table 4-F. Parallel Port Control Pins
NAME
TYPE
FUNCTION
INT
O
Interrupt.
INT flags the host controller during conditions and change of conditions defined in status
registers 1 and 2 and the HDLC status register. It is an active-low, open-drain output.
BTS0
I
Bus Type Select Bit 0. BTS0 is used with BTS1 to select between muxed, nonmuxed, serial bus
operation, and output high-Z mode.
BTS1
I
Bus Type Select Bit 1. BTS1 is used with BTS0 to select between muxed, nonmuxed, serial bus
operation, and output high-Z mode.
TS0
I
Transceiver Select Bit 0. TS0 is used with TS1 to select one of four transceivers.
TS1
I
Transceiver Select Bit 1. TS1 is used with TS0 to select one of four transceivers.
PBTS
I
Parallel Bus Type Select. PBTS is used to select between Motorola and Intel parallel bus types.
AD0 to
AD7/SDO
I/O
Data Bus or Address/Data Bus [D0 to D6], Data Bus or Address/Data Bus [D7]/Serial Port Output.
In nonmultiplexed bus operation (MUX = 0), these pins serve as the data bus. In multiplexed bus
operation (MUX = 1), they serve as an 8-bit multiplexed address/data bus.
A0 to A4
I
Address Bus. In nonmultiplexed bus operation, these pins serve as the address bus. In multiplexed bus
operation, these pins are not used and should be wired low.
RD (DS)/SCLK
I
Read Input—Data Strobe/Serial Port Clock.
RD and DS are active-low signals. DS is active high when
in multiplexed mode (Section 26).
CS
I
Chip Select.
CS must be low to read or write to the device. It is an active-low signal.
ALE (AS)/A5
I
Address Latch Enable (Address Strobe) or A6. In nonmultiplexed bus operation, this pin serves as the
upper address bit. In multiplexed bus operation, it demultiplexes the bus on a positive-going edge.
WR (R/W)/SDI
I
Write Input (Read/Write)/Serial Port Data Input, Active Low
相關PDF資料
PDF描述
RCM28DCTH CONN EDGECARD 56POS DIP .156 SLD
EET-ED2D152EA CAP ALUM 1500UF 200V 20% SNAP
RCM28DCTD CONN EDGECARD 56POS DIP .156 SLD
PLE0G681MDO1 CAP ALUM 680UF 4V 20% RADIAL
PLE0E561MCO1 CAP ALUM 560UF 2.5V 20% RADIAL
相關代理商/技術參數
參數描述
DS21Q59L 功能描述:網絡控制器與處理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q59L+ 功能描述:網絡控制器與處理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q59LN 功能描述:網絡控制器與處理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q59LN+ 功能描述:網絡控制器與處理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21S07A 制造商:Maxim Integrated Products 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*