- 您現在的位置：買賣IC網 > PDF目錄1915 > DS26900LN+ (Maxim Integrated Products)IC JTAG MUX/SWITCH 144-LQFP PDF資料下載
參數資料
| 型號： | DS26900LN+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 14/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC JTAG MUX/SWITCH 144-LQFP |
| 標準包裝： | 90 |
| 系列： | * |
| 功能： | * |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 3.14 V ~ 3.47 V |
| 電流 - 電源： | * |
| 工作溫度： | * |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 144-LQFP |
| 供應商設備封裝： | 144-LQFP（20x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
__________________________________________________________________________________________DS26900
21
DS26900
ETM
TM1
TM2
SECONDARY 1
SECONDARY 18
PREN
M[1:0] = 10 (EXTENSION)
M[1:0] = 01 (MASTER)
VDD
EXTERNAL
TEST MASTER
TEST MASTER 1
TEST MASTER 2
6
ETM
TM1
TM2
PREN
SECONDARY 19
SECONDARY 36
DS26900
5
INSTRUCTION CODE = "0xxxx"
INSTRUCTION CODE = "1xxxx"
4.1.2 Cascade Configuration Modes
The cascade configuration allows two devices to be connected together, the cascade master and the cascade
extension device. This provides access to 36 secondary ports plus the TM1 and TM2 ports (as slave ports) of the
extension device without external control logic. The cascade master has its mode pins (M[1:0]) set = 01 and the
cascade extension has its mode pins (M[1:0]) set = 10. See Table 4-1 for M0 and M1 pin settings. In Figure 4-3,
secondary ports 1 to 18 or 19 to 36 are selected by the MSB of the instruction code. Each device has a 5-bit
instruction register. The lower four LSBs have common definitions between the cascade devices, but the MSB of
the 5-bit instruction register acts as an address bit. Instructions to be executed by the cascade master have their
MSB set to 0. Instructions to be executed by the cascade extension have their MSB set to 1. The same instructions
are loaded into each device, but only the appropriate device (determined by the mode pin setting) executes the
instruction. The PREN pin on the cascade master is connected = VDD to enable internal pullup/down resistors. On
the cascade extension device, PREN is connected = VSS to disable internal pullup/down resistors.
If one or more master ports are unused, their REQ input pin(s) must be connected = VDD and the remaining unused
inputs must be connected = VDD or VSS, but cannot be left unconnected.
Figure 4-3. Two Cascaded Devices
相關PDF資料 |
PDF描述 |
|---|---|
| DS275E/T&R | IC TXRX LINE-PWR RS232 14-TSSOP |
| DS276S | IC TXRX LOW POWER RS-232 8-SOIC |
| DS2890P-000+T&R | IC POT DIGITAL 1-WIRE 100K 6TSOC |
| DS28CM00R-A00+T | IC SILICON SERIAL NUMBER SOT23-5 |
| DS30EA101SQE/NOPB | IC CABLE EQUALIZER 16LLP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS26900LN+ | 功能描述:多路器開關 IC JTAG MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| DS26900N+ | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:JTAG Multiplexer/Switch |
| DS26C31 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:CMOS QUAD TRI-STATE DIFFERENTIAL LINE DRIVER |
| DS26C31 DIE | 制造商:Texas Instruments 功能描述: |
| DS26C31_BBA3026X WAF | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。