參數資料
型號: DSP56303VL100B1
廠商: Freescale Semiconductor
文件頁數: 13/108頁
文件大?。?/td> 0K
描述: IC DSP 24BIT 100MHZ 196-BGA
標準包裝: 630
系列: DSP563xx
類型: 定點
接口: 主機接口,SSI,SCI
時鐘速率: 100MHz
非易失內存: ROM(576 B)
芯片上RAM: 24kB
電壓 - 輸入/輸出: 3.30V
電壓 - 核心: 3.30V
工作溫度: -40°C ~ 100°C
安裝類型: 表面貼裝
封裝/外殼: 196-LBGA
供應商設備封裝: 196-MAPBGA(15x15)
包裝: 托盤
DSP56303 Technical Data, Rev. 11
1-8
Freescale Semiconductor
Signals/Connections
1.7 Host Interface (HI08)
The HI08 provides a fast, 8-bit, parallel data port that connects directly to the host bus. The HI08 supports a variety
of standard buses and connects directly to a number of industry-standard microcomputers, microprocessors, DSPs,
and DMA hardware.
1.7.1
Host Port Usage Considerations
Careful synchronization is required when the system reads multiple-bit registers that are written by another
asynchronous system. This is a common problem when two asynchronous systems are connected (as they are in the
Host port). The considerations for proper operation are discussed in Table 1-10.
1.7.2
Host Port Configuration
HI08 signal functions vary according to the programmed configuration of the interface as determined by the 16 bits
in the HI08 Port Control Register.
Table 1-10.
Host Port Usage Considerations
Action
Description
Asynchronous read of receive byte
registers
When reading the receive byte registers, Receive register High (RXH), Receive register Middle
(RXM), or Receive register Low (RXL), the host interface programmer should use interrupts or poll
the Receive register Data Full (RXDF) flag that indicates data is available. This assures that the data
in the receive byte registers is valid.
Asynchronous write to transmit byte
registers
The host interface programmer should not write to the transmit byte registers, Transmit register High
(TXH), Transmit register Middle (TXM), or Transmit register Low (TXL), unless the Transmit register
Data Empty (TXDE) bit is set indicating that the transmit byte registers are empty. This guarantees
that the transmit byte registers transfer valid data to the Host Receive (HRX) register.
Asynchronous write to host vector
The host interface programmer must change the Host Vector (HV) register only when the Host
Command bit (HC) is clear. This practice guarantees that the DSP interrupt control logic receives a
stable vector.
Table 1-11.
Host Interface
Signal Name
Type
State During
Reset1,2
Signal Description
H[0–7]
HAD[0–7]
PB[0–7]
Input/Output
Input or Output
Ignored Input
Host Data—When the HI08 is programmed to interface with a non-multiplexed
host bus and the HI function is selected, these signals are lines 0–7 of the
bidirectional Data bus.
Host Address—When the HI08 is programmed to interface with a multiplexed
host bus and the HI function is selected, these signals are lines 0–7 of the
bidirectional multiplexed Address/Data bus.
Port B 0–7—When the HI08 is configured as GPIO through the HI08 Port
Control Register, these signals are individually programmed as inputs or outputs
through the HI08 Data Direction Register.
相關PDF資料
PDF描述
DSP56311VF150B1 IC DSP 24BIT 150MHZ 196-BGA
DSP56321VF200R2 IC DSP 24BIT 200MHZ 196-BGA
DSP56852VFE IC DSP 16BIT 120MHZ 81-MAPBGA
DSP56854FGE IC DSP 16BIT 120MHZ 128-LQFP
DSP56855BUE IC DSP 16BIT 120MHZ 100-LQFP
相關代理商/技術參數
參數描述
DSP56304GC66 制造商:未知廠家 制造商全稱:未知廠家 功能描述:24-Bit Digital Signal Processor
DSP56304GC80 制造商:未知廠家 制造商全稱:未知廠家 功能描述:24-Bit Digital Signal Processor
DSP56304PV66 制造商:未知廠家 制造商全稱:未知廠家 功能描述:24-Bit Digital Signal Processor
DSP56304PV80 制造商:未知廠家 制造商全稱:未知廠家 功能描述:24-Bit Digital Signal Processor
DSP56305DS 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP56305 Single Chip Channel Codec Digital Signal Processor Data Sheet