參數資料
型號： DSP56303VL100B1
廠商： Freescale Semiconductor
文件頁數： 22/108頁
文件大?。?/td> 0K
描述： IC DSP 24BIT 100MHZ 196-BGA
標準包裝： 630
系列： DSP563xx
類型： 定點
接口： 主機接口，SSI，SCI
時鐘速率： 100MHz
非易失內存： ROM（576 B）
芯片上RAM： 24kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 3.30V
工作溫度： -40°C ~ 100°C
安裝類型： 表面貼裝
封裝/外殼： 196-LBGA
供應商設備封裝： 196-MAPBGA（15x15）
包裝： 托盤
DSP56303 Technical Data, Rev. 11
1-16
Freescale Semiconductor
Signals/Connections
1.12 JTAG and OnCE Interface
The DSP56300 family and in particular the DSP56303 support circuit-board test strategies based on the IEEE
Std. 1149.1 test access port and boundary scan architecture, the industry standard developed under the
sponsorship of the Test Technology Committee of IEEE and the JTAG. The OnCE module provides a means to
interface nonintrusively with the DSP56300 core and its peripherals so that you can examine registers, memory, or
on-chip peripherals. Functions of the OnCE module are provided through the JTAG TAP signals. For programming
models, see the chapter on debugging support in the DSP56300 Family Manual.
Table 1-16.
JTAG/OnCE Interface
Signal
Name
Type
State During
Reset
Signal Description
TCK
Input
Test Clock—A test clock input signal to synchronize the JTAG test logic.
TDI
Input
Test Data Input—A test data serial input signal for test instructions and data.
TDI is sampled on the rising edge of TCK and has an internal pull-up resistor.
TDO
Output
Tri-stated
Test Data Output—A test data serial output signal for test instructions and
data. TDO is actively driven in the shift-IR and shift-DR controller states. TDO
changes on the falling edge of TCK.
TMS
Input
Test Mode Select—Sequences the test controller’s state machine. TMS is
sampled on the rising edge of TCK and has an internal pull-up resistor.
TRST
Input
Test Reset—Initializes the test controller asynchronously. TRST has an
internal pull-up resistor. TRST must be asserted after powerup.
DE
Input/ Output
(open-drain)
Input
Debug Event—As an input, initiates Debug mode from an external command
controller, and, as an open-drain output, acknowledges that the chip has
entered Debug mode. As an input, DE causes the DSP56300 core to finish
executing the current instruction, save the instruction pipeline information,
enter Debug mode, and wait for commands to be entered from the debug
serial input line. This signal is asserted as an output for three clock cycles
when the chip enters Debug mode as a result of a debug request or as a result
of meeting a breakpoint condition. The DE has an internal pull-up resistor.
This signal is not a standard part of the JTAG TAP controller. The signal
connects directly to the OnCE module to initiate debug mode directly or to
provide a direct external indication that the chip has entered Debug mode. All
other interface with the OnCE module must occur through the JTAG port.
Note: All inputs are 5 V tolerant.
相關PDF資料
PDF描述
DSP56311VF150B1 IC DSP 24BIT 150MHZ 196-BGA
DSP56321VF200R2 IC DSP 24BIT 200MHZ 196-BGA
DSP56852VFE IC DSP 16BIT 120MHZ 81-MAPBGA
DSP56854FGE IC DSP 16BIT 120MHZ 128-LQFP
DSP56855BUE IC DSP 16BIT 120MHZ 100-LQFP
相關代理商/技術參數
參數描述
DSP56304GC66 制造商:未知廠家 制造商全稱:未知廠家 功能描述:24-Bit Digital Signal Processor
DSP56304GC80 制造商:未知廠家 制造商全稱:未知廠家 功能描述:24-Bit Digital Signal Processor
DSP56304PV66 制造商:未知廠家 制造商全稱:未知廠家 功能描述:24-Bit Digital Signal Processor
DSP56304PV80 制造商:未知廠家 制造商全稱:未知廠家 功能描述:24-Bit Digital Signal Processor
DSP56305DS 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP56305 Single Chip Channel Codec Digital Signal Processor Data Sheet
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*