參數資料
型號： DSPIC30F6010-20E/PF
廠商： Microchip Technology
文件頁數： 71/110頁
文件大?。?/td> 0K
描述： IC DSPIC MCU/DSP 144K 80TQFP
產品培訓模塊： Asynchronous Stimulus
標準包裝： 90
系列： dsPIC™ 30F
核心處理器： dsPIC
芯體尺寸： 16-位
速度： 20 MIPS
連通性： CAN，I²C，SPI，UART/USART
外圍設備： 高級欠壓探測/復位，LVD，電機控制 PWM，QEI，POR，PWM，WDT
輸入/輸出數： 68
程序存儲器容量： 144KB（48K x 24）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 4K x 8
RAM 容量： 8K x 8
電壓 - 電源 (Vcc/Vdd)： 2.5 V ~ 5.5 V
數據轉換器： A/D 16x10b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 80-TQFP
包裝： 托盤
配用： DM300019-ND - BOARD DEMO DSPICDEM 80L STARTER
AC164314-ND - MODULE SKT FOR PM3 80PF
DM300020-ND - BOARD DEV DSPICDEM MC1 MOTORCTRL
其它名稱： DSPIC30F601020EPF
2006 Microchip Technology Inc.
DS70119E-page 61
dsPIC30F6010
10.0
TIMER2/3 MODULE
This section describes the 32-bit General Purpose
Timer module (Timer2/3) and associated operational
modes. Figure 10-1 depicts the simplified block dia-
gram of the 32-bit Timer2/3 module. Figure 10-2 and
show
Timer2/3
configured
as
two
independent
16-bit
timers;
Timer2
and
Timer3,
respectively.
The Timer2/3 module is a 32-bit timer, which can be
configured as two 16-bit timers, with selectable operat-
ing modes. These timers are utilized by other
peripheral modules such as:
Input Capture
Output Compare/Simple PWM
The following sections provide a detailed description,
including setup and control registers, along with asso-
ciated block diagrams for the operational modes of the
timers.
The 32-bit timer has the following modes:
Two independent 16-bit timers (Timer2 and
Timer3) with all 16-bit operating modes (except
Asynchronous Counter mode)
Single 32-bit Timer operation
Single 32-bit Synchronous Counter
Further, the following operational characteristics are
supported:
ADC Event Trigger
Timer Gate Operation
Selectable Prescaler Settings
Timer Operation during Idle and Sleep modes
Interrupt on a 32-bit Period Register Match
These operating modes are determined by setting the
appropriate bit(s) in the 16-bit T2CON and T3CON
SFRs.
For 32-bit timer/counter operation, Timer2 is the least
significant word and Timer3 is the most significant word
of the 32-bit timer.
16-bit Mode: In the 16-bit mode, Timer2 and Timer3
can be configured as two independent 16-bit timers.
Each timer can be set up in either 16-bit Timer mode or
16-bit Synchronous Counter mode. See Section 9.0
“Timer1 Module”, Timer1 Module, for details on these
two operating modes.
The only functional difference between Timer2 and
Timer3 is that Timer2 provides synchronization of the
clock prescaler output. This is useful for high-frequency
external clock inputs.
32-bit Timer Mode: In the 32-bit Timer mode, the timer
increments on every instruction cycle up to a match
value, preloaded into the combined 32-bit period regis-
ter PR3/PR2, then resets to 0 and continues to count.
For synchronous 32-bit reads of the Timer2/Timer3
pair, reading the least significant word (TMR2 register)
will cause the most significant word to be read and
latched
into
a
16-bit
holding
register,
termed
TMR3HLD.
For synchronous 32-bit writes, the holding register
(TMR3HLD) must first be written to. When followed by
a write to the TMR2 register, the contents of TMR3HLD
will be transferred and latched into the MSB of the
32-bit timer (TMR3).
32-bit Synchronous Counter Mode: In the 32-bit
Synchronous Counter mode, the timer increments on
the rising edge of the applied external clock signal,
which is synchronized with the internal phase clocks.
The timer counts up to a match value preloaded in the
combined 32-bit period register PR3/PR2, then resets
to ‘0’ and continues.
When the timer is configured for the Synchronous
Counter mode of operation and the CPU goes into the
Idle mode, the timer will stop incrementing, unless the
TSIDL (T2CON<13>) bit = 0. If TSIDL = 1, the timer
module logic will resume the incrementing sequence
upon termination of the CPU Idle mode.
Note: This data sheet summarizes features of this group
of dsPIC30F devices and is not intended to be a complete
reference source. For more information on the CPU,
peripherals, register descriptions and general device
functionality, refer to the “dsPIC30F Family Reference
Manual” (DS70046).
Note:
Timer2 is a ‘Type B’ timer and Timer3 is a
‘Type C’ timer. Please refer to the appro-
priate timer type in Section 24.0 “Electri-
cal Characteristics” of this document.
Note:
For 32-bit timer operation, T3CON control
bits are ignored. Only T2CON control bits
are used for setup and control. Timer 2
clock and gate inputs are utilized for the
32-bit timer module, but an interrupt is
generated with the Timer3 interrupt flag
(T3IF) and the interrupt is enabled with the
Timer3 Interrupt Enable bit (T3IE).
相關PDF資料
PDF描述
DSPIC30F6010A-30I/PF IC DSPIC MCU/DSP 144K 80TQFP
DSPIC30F6013A-30I/PF IC DSPIC MCU/DSP 132K 80TQFP
DSPIC30F6014-30I/PF IC DSPIC MCU/DSP 144K 80TQFP
DSPIC33EP512MU814-I/PL IC DSC 16BIT 512KB 144LQFP
DSPIC33EP64MC504-E/TL IC DSC 16BIT 64KB FLASH 44-VTLA
相關代理商/技術參數
參數描述
DSPIC30F6010-20I/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 20MHz 144KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F6010-20I/PF 制造商:Microchip Technology Inc 功能描述:16BIT 20MIPS DSPIC SMD 30F6010
DSPIC30F6010-30I/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 30MHz 144KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F6010-30I/PF 制造商:Microchip Technology Inc 功能描述:16BIT 30MIPS DSPIC SMD 30F6010
DSPIC30F6010-30I/PF 制造商:Microchip Technology Inc 功能描述:Digital Signal Processor IC Frequency Ma
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*