參數資料
型號： HYB18L128160BF
廠商： QIMONDA
英文描述： DRAMs for Mobile Applications 128-Mbit Mobile-RAM
中文描述： 針對移動應用的DRAM 128 - Mbit的移動RAM
文件頁數： 7/55頁
文件大小： 1399K
代理商： HYB18L128160BF
Data Sheet
7
Rev. 1.71, 2007-01
05282004-NZNK-8T0D
HY[B/E]18L128160B[C/F]-7.5
128-Mbit Mobile-RAM
OverviewPin Definition and Description
1.4
Pin Definition and Description
Table 5
Ball
CLK
CKE
Pin Description
Type
Input
Input
Detailed Function
Clock:
all inputs are sampled on the positive edge of CLK.
Clock Enable:
CKE HIGH activates and CKE LOW deactivates internal clock signals,
device input buffers and output drivers. Taking CKE LOW provides PRECHARGE
POWER-DOWN and SELF REFRESH operation (all banks idle), ACTIVE POWER-
DOWN (row active in any bank) or SUSPEND (access in progress). Input buffers,
excluding CLK and CKE are disabled during power-down. Input buffers, excluding CKE
are disabled during SELF REFRESH.
Chip Select:
All commands are masked when CS is registered HIGH. CS provides for
external bank selection on systems with multiple memory banks. CS is considered part of
the command code.
Command Inputs:
RAS, CAS and WE (along with CS) define the command being
entered.
Data Inputs/Output:
Bi-directional data bus (16 bit)
Input/Output Mask:
input mask signal for WRITE cycles and output enable for READ
cycles. For WRITEs, DQM acts as a data mask when HIGH. For READs, DQM acts as
an output enable and places the output buffers in High-Z state when HIGH (two clocks
latency).
LDQM corresponds to the data on DQ0 - DQ7; UDQM to the data on DQ8 - DQ15.
Bank Address Inputs:
BA0 and BA1 define to which bank an ACTIVATE, READ, WRITE
or PRECHARGE command is being applied. BA0, BA1 also determine which mode
register is to be loaded during a MODE REGISTER SET command (MRS or EMRS).
Address Inputs:
A0 - A11 define the row address during an ACTIVE command cycle. A0
- A8 define the column address during a READ or WRITE command cycle. In addition,
A10 (= AP) controls Auto Precharge operation at the end of the burst read or write cycle.
During a PRECHARGE command, A10 (= AP) in conjunction with BA0, BA1 controls
which bank(s) are to be precharged: if A10 is HIGH, all four banks will be precharged
regardless of the state of BA0 and BA1; if A10 is LOW, BA0, BA1 define the bank to be
precharged. During MODE REGISTER SET commands, the address inputs hold the
op-code to be loaded.
Supply
I/O Power Supply:
Isolated power for DQ output buffers for improved noise immunity:
V
DDQ
= 1.70V to 1.95V
Supply
I/O Ground
Supply
Power Supply:
Power for the core logic and input buffers, V
DD
= 1.70V to 1.95V
Supply
Ground
–
No Connect
CS
Input
RAS, CAS,
WE
DQ0 - DQ15 I/O
LDQM,
UDQM
Input
Input
BA0, BA1
Input
A0 - A11
Input
V
DDQ
V
SSQ
V
DD
V
SS
N.C.
相關PDF資料
PDF描述
HYB18L256160B DRAMs for Mobile Applications 256-Mbit Mobile-RAM
HYMP112S64LMP8-C4 DDR2 SDRAM SO-DIMM
HYMP112S64LMP8-C5 DDR2 SDRAM SO-DIMM
HYMP112S64LMP8-E3 BNC FEMALE TO RCA MALE COUPLER
HYMP112S64LMP8-E4 DDR2 SDRAM SO-DIMM
相關代理商/技術參數
參數描述
HYB18L128160BF-7.5 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:BJAWBMSpecialty DRAMs Mobile-RAM
HYB18L128160BF-75 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:DRAMs for Mobile Applications
HYB18L256160B 制造商:QIMONDA 制造商全稱:QIMONDA 功能描述:DRAMs for Mobile Applications 256-Mbit Mobile-RAM
HYB18L256160BC-7.5 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:BJAWBMSpecialty DRAMs Mobile-RAM
HYB18L256160BC-75 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:DRAMs for Mobile Applications
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*