- 您現在的位置：買賣IC網 > PDF目錄9574 > IDT82V3280DQG8 (IDT, Integrated Device Technology Inc)IC PLL WAN SE STRATUM 2 100-TQFP PDF資料下載
參數資料
| 型號： | IDT82V3280DQG8 |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 103/171頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PLL WAN SE STRATUM 2 100-TQFP |
| 標準包裝： | 750 |
| 類型： | 時鐘/頻率發生器，多路復用器 |
| PLL： | 是 |
| 主要目的： | 以太網，SONET/SDH，Stratum |
| 輸入： | CMOS，LVDS，PECL |
| 輸出： | CMOS，LVDS，PECL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 14:9 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 622.08MHz |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP 裸露焊盤 |
| 供應商設備封裝： | 100-TQFP-EP（14x14） |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | 82V3280DQG8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁當前第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁
IDT82V3280
WAN PLL
Functional Description
37
December 9, 2008
3.11
T0 / T4 DPLL OUTPUT
The DPLL output is locked to the selected input clock. According to
the phase-compared result of the feedback and the selected input clock,
and the DPLL output frequency offset, the PFD output is limited and the
DPLL output is frequency offset limited.
3.11.1
PFD OUTPUT LIMIT
The PFD output is limited to be within ±1 UI or within the coarse
phase limit (refer to Chapter 3.7.1.2 Coarse Phase Loss), as determined
by the MULTI_PH_APP bit.
3.11.2
FREQUENCY OFFSET LIMIT
The DPLL output is limited to be within the DPLL hard limit (refer to
For T0 DPLL, the integral path value can be frozen when the DPLL
hard limit is reached. This function, enabled by the T0_LIMT bit, will min-
imize the subsequent overshoot when T0 DPLL is pulling in.
3.11.3
PBO (T0 ONLY)
The PBO function is only supported by the T0 path.
When a PBO event is triggered, the phase offset of the selected input
clock with respect to the T0 DPLL output is measured. The device then
automatically accounts for the measured phase offset and compensates
an appropriate phase offset into the DPLL output so that the phase tran-
sients on the T0 DPLL output are minimized.
A PBO event is triggered if any one of the following conditions
occurs:
T0 selected input clock switches (the PBO_EN bit is ‘1’);
T0 DPLL exits from Holdover mode or Free-Run mode (the
PBO_EN bit is ‘1’);
Phase-time changes on the T0 selected input clock are greater
than a programmable limit over an interval of less than 0.1 sec-
onds (the PH_MON_PBO_EN bit is ‘1’).
For the first two conditions, the phase transients on the T0 DPLL out-
put are minimized to be no more than 0.61 ns with PBO. The PBO can
also be frozen at the current phase offset by setting the PBO_FREZ bit.
When the PBO is frozen, the device will ignore any further PBO events
triggered by the above two conditions, and maintain the current phase
offset. When the PBO is disabled, there may be a phase shift on the T0
DPLL output and the T0 DPLL output tracks back to 0 degree phase off-
set with respect to the T0 selected input clock.
The last condition is specially for stratum 2 and 3E clocks. The PBO
requirement specified in the Telcordia GR-1244-CORE is: ‘Input phase-
time changes of 3.5 s or greater over an interval of less than 0.1 sec-
onds or less shall be built-out by stratum 2 and 3E clocks to reduce the
resulting clock phase-time change to less than 50 ns. Phase-time
changes of 1.0 s or less over an interval of 0.1 seconds shall not be
built-out.’ Based on this requirement, phase-time changes of more than
1.0 s but less than 3.5 s that occur over an interval of less than 0.1
seconds may or may not be built-out.
An integrated Phase Transient Monitor can be enabled by the
PH_MON_EN bit to monitor the phase-time changes on the T0 selected
input clock. When the phase-time changes are greater than a limit over
an interval of less than 0.1 seconds, a PBO event is triggered and the
phase transients on the DPLL output are absorbed. The limit is pro-
grammed by the PH_TR_MON_LIMT[3:0] bits, and can be calculated as
follows:
Limit (ns) = (PH_TR_MON_LIMT[3:0] + 7) X 156
The phase offset induced by PBO will never result in a coarse or fine
phase loss.
3.11.4
PHASE OFFSET SELECTION (T0 ONLY)
The phase offset of the T0 selected input clock with respect to the T0
DPLL output can be adjusted. If the device is configured as the Master,
the PH_OFFSET_EN bit determines whether the input-to-output phase
offset is enabled; if the device is configured as the Slave, the input-to-
output phase offset is always enabled. If enabled, the input-to-output
phase offset can be adjusted by setting the PH_OFFSET[9:0] bits.
The input-to-output phase offset can be calculated as follows:
Phase Offset (ns) = PH_OFFSET[9:0] X 0.61
3.11.5
FOUR PATHS OF T0 / T4 DPLL OUTPUTS
The T0 DPLL output and the T4 DPLL output are phase aligned with
the T0 selected input clock and the T4 selected input clock respectively
every 125 s period. Each DPLL has four output paths.
3.11.5.1
T0 Path
The four paths for T0 DPLL output are as follows:
77.76 MHz path - outputs a 77.76 MHz clock;
16E1/16T1 path - outputs a 16E1 or 16T1 clock, as selected by
the IN_SONET_SDH bit;
GSM/OBSAI/16E1/16T1 path - outputs a GSM, OBSAI, 16E1 or
16T1 clock, as selected by the T0_GSM_OBSAI_16E1_16T1_
SEL[1:0] bits;
12E1/24T1/E3/T3 path - outputs a 12E1, 24T1, E3 or T3 clock,
as selected by the T0_12E1_24T1_E3_T3_SEL[1:0] bits.
T0 selected input clock is compared with a T0 DPLL output for DPLL
locking. The output can only be derived from the 77.76 MHz path or the
16E1/16T1 path. The output path is automatically selected and the out-
put is automatically divided to get the same frequency as the T0
selected input clock.
The T0 DPLL 77.76 MHz output or an 8 kHz signal derived from it
can be provided for the T4 DPLL input clock selection (refer to
T0 DPLL outputs are provided for T0/T4 APLL or device output pro-
cess.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B2X-MW-F1 | CONVERTER MOD DC/DC 5.2V 100W |
| VE-B2R-MW-F4 | CONVERTER MOD DC/DC 7.5V 100W |
| VE-B2P-MW-F2 | CONVERTER MOD DC/DC 13.8V 100W |
| VE-B2N-MW-F1 | CONVERTER MOD DC/DC 18.5V 100W |
| IDT82V3355TFG | IC PLL WAN SYNC ETH 64-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT82V3280EQG | 功能描述:IC PLL WAN SE STRATUM 2 100TQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| IDT82V3280EQG8 | 制造商:Integrated Device Technology Inc 功能描述:IC PLL WAN SE STRATUM 2 100TQFP |
| IDT82V3280EQGBLANK | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:WAN PLL |
| IDT82V3280PF | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:WAN PLL |
| IDT82V3280PFBLANK | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:WAN PLL |
發布緊急采購，3分鐘左右您將得到回復。