- 您現在的位置：買賣IC網 > PDF目錄1931 > KSZ8841-PMQL (Micrel Inc)IC MAC CTRLR 32BIT 128-PQFP PDF資料下載
參數資料
| 型號： | KSZ8841-PMQL |
| 廠商： | Micrel Inc |
| 文件頁數： | 13/74頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MAC CTRLR 32BIT 128-PQFP |
| 應用說明： | AN-142 Wake-on-LAN and Wake-Up Event |
| 標準包裝： | 66 |
| 控制器類型： | 以太網控制器，MAC |
| 接口： | 總線 |
| 電源電壓： | 3.1 V ~ 3.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 1080 (CN2011-ZH PDF) |
| 配用： | 576-1633-ND - BOARD EVALUATION KSZ8841-PMQL |
| 其它名稱： | 576-2117 KSZ8841-PMQL-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
Micrel, Inc.
KSZ8841-PMQL
October 2007
20
M9999-100407-1.5
LinkMD Cable Diagnostics
The KSZ8841-PMQL LinkMD uses time domain reflectometry (TDR) to analyze the cabling plant for common cabling
problems such as open circuits, short circuits, and impedance mismatches.
LinkMD works by sending a pulse of known amplitude and duration down the MDI and MDI-X pairs and then analyzes
the shape of the reflected signal. Timing the pulse duration gives an indication of the distance to the cabling fault with a
maximum distance of 200m and an accuracy of +/–2m.
Access
LinkMD is initiated by accessing register P1VCT, the LinkMD Control/Status register, in conjunction with register
P1CR4, the 100BASE-TX PHY Controller register.
Usage
LinkMD can be run at any time. To use LinkMD, disable HP Auto-MDIX by writing a ‘1’ to P1CR4[10] to enable manual
control over the pair used to transmit the LinkMD pulse. The self-clearing cable diagnostic test enable bit, P1VCT[15], is
set to ‘1’ to start the test on this pair.
When bit P1VCT[15] returns to ‘0’, the test is complete. The test result is returned in bits P1VCT[14-13] and the
distance is returned in bits P1VCT[8-0]. The cable diagnostic test results are as follows:
00 = Valid test, normal condition
01 = Valid test, open circuit in cable
10 = Valid test, short circuit in cable
11 = Invalid test, LinkMD failed
If P1VCT[14-13]=11 case, this indicates an invalid test, occurs when the KSZ8841-PMQL is unable to shut down the
link partner. In this instance, the test is not run, since it would be impossible for the KSZ8841-PMQL to determine if the
detected signal is a reflection of the signal generated or a signal from another source.
Cable distance (in meters) can approximately be determined by the following formula:
Distance = P1VCT[8-0] x 0.4m
This constant may be calibrated for different cabling conditions, including cables with a velocity of propagation that
varies significantly from the norm.
Media Access Control (MAC) and other
The KSZ8841-PMQL strictly abides by IEEE 802.3 standards to maximize compatibility.
Inter Packet Gap (IPG)
If a frame is successfully transmitted, the minimum 96-bits time for IPG is between the two consecutive packets. If the
current packet is experiencing collisions, the minimum 96-bits time for IPG is from carrier sense to the next transmit
packet.
Back-Off Algorithm
The KSZ8841-PMQL implements the IEEE standard 802.3 binary exponential back-off algorithm in half-duplex mode.
After 16 collisions, the packet is dropped.
Late Collision
If a transmit packet experiences collisions after 512 bit times of the transmission, the packet is dropped.
Flow Control
The KSZ8841-PMQL supports standard 802.3x flow control frames on both transmit and receive sides.
On the receive side, if the KSZ8841-PMQL receives a pause control frame, the KSZ8841-PMQL will not transmit the
next normal frame until the timer, specified in the pause control frame, expires. If another pause frame is received
before the current timer expires, the timer will be updated with the new value in the second pause frame. During this
period (while it is flow controlled), only flow control packets from the KSZ8841-PMQL are transmitted.
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8842-16MBLI TR | IC ETHERNET SW 2PORT 100LFBGA |
| KSZ8842-32MVLI | IC SWITCH ETH 2P 32BIT 128LQFP |
| KSZ8842-PMBL AM TR | IC ETHERNET SW 2PORT 100LFBGA |
| KSZ8842-PMQLI | IC ETHERNET SW 2PORT PCI 128PQFP |
| KSZ8851-16MLLI TR | IC MAC CTLR 1PORT W/BUS 48LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8841-PMQL-EVAL | 功能描述:以太網開發工具 KSZ8841-PMQL Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8841-PMQLI | 功能描述:以太網 IC Single Ethernet Port + 32-bit/33MHz PCI interface, Ind Temp (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8842 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with PCI Interface |
| KSZ8842-16 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface |
| KSZ8842-16_08 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface |
發布緊急采購，3分鐘左右您將得到回復。