參數資料
型號: KSZ8841-PMQL
廠商: Micrel Inc
文件頁數: 27/74頁
文件大小: 0K
描述: IC MAC CTRLR 32BIT 128-PQFP
應用說明: AN-142 Wake-on-LAN and Wake-Up Event
標準包裝: 66
控制器類型: 以太網控制器,MAC
接口: 總線
電源電壓: 3.1 V ~ 3.5 V
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 128-BFQFP
供應商設備封裝: 128-PQFP(14x20)
包裝: 托盤
產品目錄頁面: 1080 (CN2011-ZH PDF)
配用: 576-1633-ND - BOARD EVALUATION KSZ8841-PMQL
其它名稱: 576-2117
KSZ8841-PMQL-ND
Micrel, Inc.
KSZ8841-PMQL
October 2007
33
M9999-100407-1.5
Bit
Default
Description
Provides interrupt line routing information. The basic input/output system
(BIOS) writes the routing information into to this field when it initialized and
configures the system. The value in this field indicates which input of the
system interrupt controller is connected to the K8841P’s interrupt pin. The
driver can use this information to determine priority and vector information.
Values in this field are system architecture specific.
The following table shows the access rules of the register.
Category
Description
Value after hardware reset
0x281401XX
Capabilities ID Register (CCID Offset 50H)
The CCID register is a read-only register that provides information on the KSZ8841-PMQL power management
capabilities. The following table shows the CCID register bit fields. The CCID register bits [31-16] are mirrored with
PMCR register bits [15-0].
Bit
Default
Description
31
0
PME Support D3 (cold)
If this bit is set, the KSZ8841-PMQL asserts PME in D3(cold) power state.
Otherwise,
the KSZ8841-PMQL does not assert PME in D3(cold).
The value of this bit is loaded from the PME_D3_cold bit in the EEPROM.
30
1
PME Support D3 (hot)
The value of this bit is 1, indicating that the KSZ8841-PMQL may assert
PME in
D3(hot) power state.
29
0
PME Support D2
If this bit is set, the KSZ8841-PMQL asserts PME in D2 power state.
Otherwise, the
KSZ8841-PMQL does not assert PME in D2 state.
The value of this bit is loaded from the PME_D2 bit in the EEPROM.
28
0
PME Support D1
If this bit is set, the KSZ8841-PMQL asserts PME in D1 power state.
Otherwise, the
KSZ8841-PMQL does not assert PME in D1 state.
The value of this bit loaded from the PME_D1 bit in the EEPROM.
27
0
PME Support D0
1
The value of this bit is 0, indicating that the KSZ8841-PMQL does not
assert PME in
D0 power state.
26
0
D2 Support
If this bit is set, it indicates that the KSZ8841-PMQL support D2 power
state.
The value of this bit is loaded from the D2_SUP bit in the EEPROM.
1 References to D0, D1, D2, and D3 are power management states defined in a similar fashion to the way they are defined for PCI.
For more information, refer to the PCI specification at www.pcisig.com/specifications/conventional/pcipm1.2.pdf.
相關PDF資料
PDF描述
KSZ8842-16MBLI TR IC ETHERNET SW 2PORT 100LFBGA
KSZ8842-32MVLI IC SWITCH ETH 2P 32BIT 128LQFP
KSZ8842-PMBL AM TR IC ETHERNET SW 2PORT 100LFBGA
KSZ8842-PMQLI IC ETHERNET SW 2PORT PCI 128PQFP
KSZ8851-16MLLI TR IC MAC CTLR 1PORT W/BUS 48LQFP
相關代理商/技術參數
參數描述
KSZ8841-PMQL-EVAL 功能描述:以太網開發工具 KSZ8841-PMQL Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
KSZ8841-PMQLI 功能描述:以太網 IC Single Ethernet Port + 32-bit/33MHz PCI interface, Ind Temp (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8842 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with PCI Interface
KSZ8842-16 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface
KSZ8842-16_08 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface