參數資料
型號： LAN9116
廠商： SMSC Corporation
英文描述： Highly Efficient Single-Chip 10/100 Non-PCI Ethernet Controller
中文描述： 高效的單芯片10/100非PCI以太網控制器
文件頁數： 18/126頁
文件大?。?/td> 831K
代理商： LAN9116
Highly Efficient Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Revision 1.1 (05-17-05)
18
SMSC LAN9116
DATASHEET
70
Wakeup Indicator
PME
O8/OD8
1
When programmed to do so, is
asserted when the LAN9116 detects
a wake event and is requesting the
system to wake up from the
associated sleep state. The polarity
and buffer type of this signal is
programmable.
Note:
Detection of a Power
Management Event, and
assertion of the PME signal
will not wakeup the
LAN9116. The LAN9116 will
only wake up when it
detects a host write cycle
(assertion of nCS and
nWR). Although any write to
the LAN9116, regardless of
the data written, will wake-
up the device when it is in a
power-saving mode, it is
required that the
BYTE_TEST register be
used for this purpose.
100,99
,98
General Purpose
I/O data,
nLED1 (Speed
Indicator),
nLED2 (Link &
Activity Indicator),
nLED3 (Full-
Duplex
Indicator
)
.
GPIO[2:0]/
LED[3:1]
IS/O12/
OD12
3
General Purpose I/O data:
These
three general-purpose signals are
fully programmable as either push-
pull output, open-drain output or input
by writing the GPIO_CFG
configuration register in the CSR’s.
They are also multiplexed as GP LED
connections.
GPIO signals are Schmitt-triggered
inputs. When configured as LED
outputs these signals are open-drain.
nLED1 (Speed Indicator).
This
signal is driven low when the
operating speed is 100Mbs, during
auto-negotiation and when the cable
is disconnected. This signal is driven
high only during 10Mbs operation.
nLED2 (Link & Activity Indicator).
This signal is driven low (LED on)
when the LAN9116 detects a valid
link. This signal is pulsed high (LED
off) for 80mS whenever transmit or
receive activity is detected. This
signal is then driven low again for a
minimum of 80mS, after which time it
will repeat the process if TX or RX
activity is detected. Effectively, LED2
is activated solid for a link. When
transmit or receive activity is sensed
LED2 will flash as an activity
indicator.
nLED3 (Full-Duplex Indicator).
This
signal is driven low when the link is
operating in full-duplex mode.
Table 2.5 System and Power Signals (continued)
PIN
NO.
NAME
SYMBOL
BUFFER
TYPE
NUM
PINS
DESCRIPTION
相關PDF資料
PDF描述
LAN9117 HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER
LAN9117-MD HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER
LAN9117-MT HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER
LAN9118 HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER
LAN9118-MD HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER
相關代理商/技術參數
參數描述
LAN9116-MD 功能描述:以太網 IC Efficient Sngl Chip 10/100 Ethrnt RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN9116-MT 功能描述:以太網 IC Ethernet IC 32bit Superior Perf RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN9117 制造商:SMSC 制造商全稱:SMSC 功能描述:HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER
LAN9117-MD 功能描述:以太網 IC HiPerfrm Sngl-Chip 10/100 Ethrnt RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN9117-MT 功能描述:以太網 IC HiPerfrm Sngl-Chip 10/100 Ethrnt RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*