- 您現在的位置：買賣IC網 > PDF目錄45037 > M37735MHBXXXFP 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M37735MHBXXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件頁數： | 53/93頁 |
| 文件大小： | 1802K |
| 代理商： | M37735MHBXXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁
54
MITSUBISHI MICROCOMPUTERS
M37735MHBXXXFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
OSCILLATION CIRCUIT
In the oscillation circuit, two kinds of clock circuits are built-in. One is
the main-clock oscillation circuit which uses the XIN and XOUT pins,
and the other is the sub-clock (32 kHz) oscillation circuit which uses
the XCIN and the XCOUT pins.
Either of these two oscillation circuits can output the system clock,
and it can be selected.
Figure 61 shows the oscillation circuit example with a ceramic
resonator or a quartz-crystal oscillator connected. The circuit
constants such as capacitance depend on a resonator/oscillator, and
these constants shall be set to the resonator/oscillator manufacture’s
recommended value.
Figure 62 shows the example of the external clock input circuit.
When inputting the main clock externally, the main-clock oscillation
circuit stops operating and power dissipation could be conserved by
setting the main clock external input selection bit (bit 1 of the oscillation
circuit control register 1, refer to Figure 63) to “1”. Note that this bit
also has the function to select a return factor from STP state (refer to
the section on the STANDBY FUNCTION.) Additionally, write to the
oscillation circuit control register 1 as the flow shown in Figure 64.
Pins XCIN and XCOUT of the sub-clock oscillation circuit are also used
as I/O ports P77 and P76, and these functions are selected with the
port-XC selection bit described below.
From the time during reset to the time after releasing reset, only the
main-clock oscillation circuit operates and the main clock is selected
as the system clock. Furthermore, at this time, the sub-clock oscillation
circuit stops and pins XCIN and XCOUT become I/O ports (P77, P76).
When the port-XC selection bit (bit 4 of the oscillation circuit control
register 0) is set to “1” in this condition, I/O ports P77 and P76 are
switched to pins XCIN and XCOUT, and then, oscillation starts in the
sub-clock oscillation circuit.
XIN
XOUT
XCIN
P76
Left open
External oscillation circuit
Vcc
Vss
Vcc
Vss
(P76 as I/O port)
External oscillation circuit
When inputting the main clock externally, set the main clock
external input selection bit to “1”. Then, leave the XOUT pin
open.
When inputting the sub clock externally, set the sub-clock
external input selection bit to “1”. Then, port P76 becomes an
I/O port.
Fig. 62 External clock input circuit
When inputting the sub clock externally, set the sub-clock external
input selection bit (bit 2 of the oscillation circuit control register 1) to
“1” before selecting pins XCIN and XCOUT with the port-Xc selection
bit. When the sub-clock external input selection bit is set to “1”, port
P76 becomes an I/O port (or an analog input AN6). Note that this bit
also has the function to select a return factor from STP state (refer to
the section on the STANDBY FUNCTION.)
When the sub-clock output selection bit (bit 1 of the port function
control register, refer to Figure 11) is set to “1” under the condition of
the port-Xc selection bit = “1”, the sub-clock
φ SUB is output from port
P67. Accordingly, the sub-clock 32 kHz can be supplied for external
devices.
Rf
Rd
CIN
COUT
XIN
XOUT
XCIN
XCOUT
Rcf
Rcd
CCIN
CCOUT
(32 kHz)
In this case, sub-clock oscillation circuit is used.
(Port-Xc selection bit is “1”)
Rf
Rd
CIN
COUT
XIN
XOUT
P77
P76
(P77, P76 as I/O port)
In this case, sub-clock oscillation circuit is not used.
( Port-Xc selection bit is “0”)
Fig. 61 Oscillation circuit example with external resonator or quartz-crystal oscillator
相關PDF資料 |
PDF描述 |
|---|---|
| M37735MHLXXXHP | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37735S4LHP | 16-BIT, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37736EHBGS | 16-BIT, UVPROM, 24 MHz, MICROCONTROLLER, CQCC100 |
| M37736EHBXXXGP | 16-BIT, OTPROM, 25 MHz, MICROCONTROLLER, PQFP100 |
| M37736EHBGS | 16-BIT, UVPROM, 25 MHz, MICROCONTROLLER, CQCC100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37735MHL | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37735MHL-143HP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:PROM VERSION OF M37735MHLXXXHP |
| M37735MHLXXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37735S4BFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37735S4LHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。