參數資料
型號： MAX1358BETL+W
廠商： Maxim Integrated Products
文件頁數： 32/71頁
文件大?。?/td> 0K
描述： DAS 16BIT DUAL 10:1 40-TQFN
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 50
類型： 數據采集系統（DAS）
分辨率（位）： 16 b
采樣率（每秒）： 21.94k
數據接口： MICROWIRE?，QSPI?，串行，SPI?
電壓電源： 模擬和數字
電源電壓： 1.8 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 40-WFQFN 裸露焊盤
供應商設備封裝： 40-TQFN-EP（6x6）
包裝： 托盤
MAX1358B
16-Bit, Data-Acquisition System with ADC, DACs,
UPIOs, RTC, Voltage Monitors, and Temp Sensor
38
______________________________________________________________________________________
RATE<2:0>: ADC conversion-rate-setting bits. These
three bits set the conversion rate of the ADC as shown
in Table 6. The initial conversion requires four conver-
sion cycles for valid data, and subsequent conversions
require only one cycle (if CONT = 1). A full-scale input
change can require up to five cycles for valid data if
the digital filter is not reset with the STRT or S bit.
MODE<2:0>: Conversion-mode bits. These three bits
determine the type of conversion for the ADC as shown
in Table 7. When the ADC finishes an offset calibration
and/or gain calibration, the MODE<2:0> bits clear to 0
hex, the ADD bit in the STATUS register asserts, and
an interrupt asserts on INT (or UPIO_ if programmed as
DRDY) if MADD is unmasked. Perform a gain calibra-
tion after achieving the desired offset (calibrated or
not). If an offset and gain calibration are performed
together (MODE<2:0> = 7 hex), the offset calibration is
performed first followed by the gain calibration, and the
C is interrupted by INT (or UPIO_ if programmed as
DRDY) if MADD is unmasked only upon completion of
both offset and gain calibration. After power-on or cali-
bration, the ADC does not begin conversions until initi-
ated by the user (see the ADCE and STRT bit
descriptions in this section and see the S bit descrip-
tions in the
MUX Register section). See the GAIN CAL
Register and OFFSET CAL Register sections for details
on system calibration.
CONVERSION MODE
MODE2
MODE1
MODE0
Normal
0
System Offset Calibration
0
1
System Gain Calibration
0
1
0
Normal
0
1
Normal
1
0
Self-Offset Calibration
1
0
1
Self-Gain Calibration
1
0
Self-Offset and Gain
Calibration
1
Table 7. Setting the ADC Conversion Mode
NOMINAL
CONTINUOUS
CONVERSION
RATE (sps)
DECIMATION
RATIO
ACTUAL
CONTINUOUS
CONVERSION
RATE (sps)
10
1096
10.01
40
274
40.04
50
220
49.87
60
183
59.95
200
55
199.48
240
46
238.51
400
27
406.35
477
23
477.02
CONTINUOUS
CONVERSION
RATE (sps)
SINGLE
CONVERSION
RATE (sps)
RATE2
RATE1
RATE0
10
2.5
0
40
10
0
1
50
12.5
0
1
0
60
15
0
1
200
50
1
0
240
60
1
0
1
400
100
1
0
477
128
1
Table 6a. Setting the ADC Conversion Rate*
*Calculate the ADC sampling rate using the following
equation:
where fHFCLK = 4.9152MHz nominally.
f
decimation ratio
S
HFCLK
=
×
448
Table 6b. Actual ADC Conversion Rates
相關PDF資料
PDF描述
MAX1406EWE IC TX/RX RS232 230KBPS 16-SOIC
MAX1414CAI+T IC DAS 16BIT LP 28-SSOP
MAX1441GUP/V+ IC PROXMITY SENSOR 2CH 20-TSSOP
MAX14502AETL+T IC CARD READER USB-SD 40-TQFN
MAX14505EWC+T IC SWITCH DUAL SPDT 12WLP
相關代理商/技術參數
參數描述
MAX1358EVKIT+ 制造商:Maxim Integrated Products 功能描述:EVALUATION KIT FOR THE MAX1358 - Boxed Product (Development Kits)
MAX1359ACGL 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX1359ACTL 制造商:Maxim Integrated Products 功能描述:16-BIT DATA-ACQUISITION SYSTEM W ADC,DACS,UPI - Rail/Tube
MAX1359ACTL+ 制造商:Maxim Integrated Products 功能描述:DATA ACQ SYS SGL ADC SGL DAC 16BIT 40TQFN EP - Rail/Tube
MAX1359ACTL+T 制造商:Maxim Integrated Products 功能描述:DATA ACQ SYS SGL ADC SGL DAC 16BIT 40TQFN EP - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*