參數資料
型號： MAX1358BETL+W
廠商： Maxim Integrated Products
文件頁數： 54/71頁
文件大?。?/td> 0K
描述： DAS 16BIT DUAL 10:1 40-TQFN
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 50
類型： 數據采集系統（DAS）
分辨率（位）： 16 b
采樣率（每秒）： 21.94k
數據接口： MICROWIRE?，QSPI?，串行，SPI?
電壓電源： 模擬和數字
電源電壓： 1.8 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 40-WFQFN 裸露焊盤
供應商設備封裝： 40-TQFN-EP（6x6）
包裝： 托盤
MAX1358B
16-Bit, Data-Acquisition System with ADC, DACs,
UPIOs, RTC, Voltage Monitors, and Temp Sensor
58
______________________________________________________________________________________
MSB
LDVD
LCPD
ADOU
SDC
CRDY
ADD
ALD
X
LSB
UPR4
UPR3
UPR2
UPR1
UPF4
UPF3
UPF2
UPF1
STATUS Register (Power-On State: 0000 000X 0000 0000)
The STATUS register contains the status bits of events in
various system blocks. Any status bits not masked in the
IMSK register cause an interrupt on INT. Some of the
status bit setting events (GPI, WAKEUP, ALARM, DRDY)
can be directed to UPIO_ to provide multiple C inter-
rupt inputs. There are no specific mask bits for the UPIO
interrupt signals since the bits are effectively masked by
selecting a different function for UPIO. The STATUS bits
always record the triggering event(s), even for masked
bits, which do not generate an interrupt on INT. It is pos-
sible to set multiple STATUS bits during a single INT
interrupt event. Clear all STATUS bits except for ADD
and ADOU by reading the STATUS register. During a
STATUS register read, INT deasserts when the first
STATUS data bit (LDVD) reads out (9th rising SCLK) and
remains deasserted until shortly after the last STATUS
data bit (~15ns). At this point, INT reasserts if any
STATUS bit is set during the STATUS register read. If the
STATUS register is partially read (i.e., the read is aborted
midway), none of the STATUS bits are cleared. New
events occurring during a STATUS register read, or
events that persist after reading the STATUS bits result in
another interrupt immediately after the STATUS register
read finishes. This is a read-only register.
LDVD: Low DVDD voltage-detector status bit. LDVD = 1
indicates DVDD is below the +1.8V threshold; otherwise
LDVD = 0. LDVD clears during the STATUS register
read as long as the condition does not persist.
Otherwise, the LDVD bit reasserts immediately. If the
DVDD low voltage detector is disabled, LDVD = 0. The
power-on default is 0.
LCPD: Low CPOUT voltage-detector status bit. LCPD =
1 indicates CPOUT is below the +2.7V threshold; other-
wise LCPD = 0. LCPD clears during the STATUS regis-
ter read as long as the condition does not persist.
Otherwise the LCPD bit reasserts immediately. LCPD =
0 when the CPOUT low voltage detector is disabled.
The power-on default is 0.
ADOU: ADC overflow/underflow status bit. ADOU = 1
indicates an ADC underflow or overflow condition in the
current ADC result. New conversions that are valid
clear the ADOU bit. ADOU = 0 when the ADC data is
valid or the ADC is disabled (ADCE = 0). An underflow
condition occurs when the ADC data is theoretically
less than 0000 hex in unipolar mode and less than
8000 hex in bipolar mode. An overflow condition occurs
when the ADC data is theoretically greater than FFFF
hex in unipolar mode and greater than 7FFF hex in
bipolar mode. Use this bit to determine the validity of
an ADC result at the maximum or minimum code values
(i.e., 0000 hex or FFFF hex for unipolar mode and 8000
hex and 7FFF hex for bipolar mode). The power-on
default is 0. Reading the STATUS register does not
clear the ADOU bit.
SDC: Signal-detect comparator status bit. When
SDC = 1, the positive input to the signal-detect compara-
tor exceeds the negative input plus the programmed
threshold voltage. The SDC bit clears during the STATUS
register read unless the condition remains true. The SDC
bit also deasserts when the signal-detect comparator
powers down (SDCE = 0). The power-on default is 0.
CRDY: High-frequency-clock ready status bit.
CRDY = 1 indicates a locked high-frequency clock to
the 32kHz reference frequency by the FLL. The CRDY
bit clears during the STATUS register read. This bit only
asserts after power-up or after enabling the FLL using
the FLLE bit. The power-on default is 0.
ADD: ADC-done status bit. ADD = 1 indicates a com-
pleted ADC conversion or calibration. Clear the ADD bit
by reading the appropriate ADC data, offset, or gain-cali-
bration registers. The ADC status bit also clears when a
new ADC result updates to the data or calibration regis-
ters (i.e., it follows the assertion level of the UPIO =
DRDY signal). Reading the STATUS register does not
clear this bit. This bit is equivalent to the DRDY signal
available through UPIO_. The power-on default is 0.
hysteresis helps eliminate chatter when running directly off
unregulated batteries. If DVDD falls below +1.3V (typ), the
power-on reset circuitry is enabled and the HYSE bit is
deasserted setting the hysteresis back to +20mV. The
power-on default is 0.
RSTE:
RESET output enable bit. Set RSTE = 1 to
enable
RESET to be controlled by the +1.8V DVDD low-
supply-voltage detector, and set RSTE = 0 to disable
this control. The power-on default is 1.
相關PDF資料
PDF描述
MAX1406EWE IC TX/RX RS232 230KBPS 16-SOIC
MAX1414CAI+T IC DAS 16BIT LP 28-SSOP
MAX1441GUP/V+ IC PROXMITY SENSOR 2CH 20-TSSOP
MAX14502AETL+T IC CARD READER USB-SD 40-TQFN
MAX14505EWC+T IC SWITCH DUAL SPDT 12WLP
相關代理商/技術參數
參數描述
MAX1358EVKIT+ 制造商:Maxim Integrated Products 功能描述:EVALUATION KIT FOR THE MAX1358 - Boxed Product (Development Kits)
MAX1359ACGL 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX1359ACTL 制造商:Maxim Integrated Products 功能描述:16-BIT DATA-ACQUISITION SYSTEM W ADC,DACS,UPI - Rail/Tube
MAX1359ACTL+ 制造商:Maxim Integrated Products 功能描述:DATA ACQ SYS SGL ADC SGL DAC 16BIT 40TQFN EP - Rail/Tube
MAX1359ACTL+T 制造商:Maxim Integrated Products 功能描述:DATA ACQ SYS SGL ADC SGL DAC 16BIT 40TQFN EP - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*