- 您現在的位置：買賣IC網 > PDF目錄1936 > MAX1441GUP/V+ (Maxim Integrated Products)IC PROXMITY SENSOR 2CH 20-TSSOP PDF資料下載
參數資料
| 型號： | MAX1441GUP/V+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 31/41頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PROXMITY SENSOR 2CH 20-TSSOP |
| 其它有關文件： | Automotive Product Guide |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 74 |
| 類型： | 觸控式傳感器 |
| 輸入類型： | 數字 |
| 輸出類型： | 數字 |
| 接口： | JTAG，串行 |
| 電流 - 電源： | 100µA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
MAX1441
Automotive, Two-Channel Proximity and
Touch Sensor
37
If the reset is caused by watchdog or external sources,
the clock source (5MHz oscillator) remains running, but
no program execution is allowed. When the reset source
is external, the user must remove the reset stimulus.
When power is applied to the device, the power-on delay
removes the stimulus automatically.
Power-On Reset Generation
The device incorporates an internal voltage reference
and comparator to monitor VDD and hold the device
in reset if the supply is out of tolerance. Once VDD has
risen above the VPOR threshold, the device generates a
power-on reset, starts the internal 20MHz, and counts
eight cycles of the derived 5MHz to ensure that Flash
is powered up and the system clock source has had
time to stabilize. The processor then exits the reset state
automatically and starts executing the program at loca-
tion 8000h.
Software can determine that a POR has occurred by
checking the power-on reset flag, POR in the WDCN
register. Software should clear the POR flag after having
read it. The POR is an asynchronous reset source.
Watchdog Timer Reset
The watchdog timer is a free-running timer with a
programmable interval. The watchdog supervises the
processor operation by requiring software to clear the
timer counter before the timeout expires. If the timer is
enabled and software fails to clear it before this interval
expires, the device is placed into a reset state. The reset
state maintains for about 90 system clock cycles. Once
the reset is removed, the processor resumes execution
at address 8000h. Software can determine if a reset is
caused by a watchdog timeout by checking the watch-
dog timer reset flag, WTRF in the WDCN register. This
flag is cleared by software only.
External Reset
If the RESET input is taken to logic 0, the device is forced
into a reset state. An external reset is accomplished by
holding the RESET pin low at least four clock cycles
while the internal 5MHz clock is running. Once the reset
state is invoked, it is maintained as long as RESET is
pulled to logic 0. When the reset state is removed, the
processor exits the reset state within four clock cycles
and begin execution at address 8000h.
If a reset state is applied while the processor is in the
stop mode, the reset causes the processor to exit the
stop mode and forces the program counter to 8000h.
The reset delay is four clock cycles.
The RESET is a bidirectional I/O. If a reset is caused by
a watchdog timer reset or an internal system reset, an
output reset pulse is also generated at the RESET pin.
This reset pulse is asserted as long as a reset source is
asserted and may not be able to drive the reset signal
out if the RESET pin is connected to an RC reset circuitry.
Connecting the RESET pin to a capacitor would not
affect the internal reset condition.
Internal System Reset
An internal system reset can occur in system program-
ming mode when the ROD bit is set to logic 1 while the
SPE bit is 1.
Timer
The device has implemented an 8-bit timer with
an 11-bit prescaler. The operation of the timer is
configurable using the Timer Control register (TCON),
Timer Frequency register (TFRQ), and the Timer Counter
register (TCNT).
The timer is enabled by setting the Timer Enable Bit
(TCON.TMREN) to 1. Once enabled, the timer starts
counting from the initial TCNT value up to the TFRQ limit.
When TCNT = TFRQ, the timer interrupt flag (TMRIF)
is set to 1. This can cause an interrupt to the CPU if
the timer interrupt is enabled (TMRIE = 1). Once the
frequency limit is reached, TCNT is reset to 0 and
continue to count up again.
The timer has two clock sources: system clock and the
32kHz clock. The selection is made using the Timer Clock
Select (TCLK) bit. Due to different clock domains, when
running off the 32kHz clock, reading of the TCNT register
is only valid when the Timer Valid Flag (TVALID) is set to
1. When running the system clock, there is no restriction
on running from TCLK. In addition, a write to TMREN
when running off the 32kHz clock can be delayed due to
synchronization between the two domains.
To increase the period between subsequent interrupts,
an 11-bit prescaler is provided to prescale the input
clock from 1 to 2048.
If the timer is enabled and running off the 32kHz clock
source prior to the stop mode entry, the timer continues
to run and invoke a stop mode exit if the interrupt is
enabled.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX14502AETL+T | IC CARD READER USB-SD 40-TQFN |
| MAX14505EWC+T | IC SWITCH DUAL SPDT 12WLP |
| MAX14523BATA/V+T | IC CURRENT LIMIT SWITCH 8TDFN |
| MAX1452AAE+T | IC SENSOR SIGNAL COND 16-SSOP |
| MAX14531EEWC+T | IC USB SWITCH DP3T 12WLP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1441IUP+ | 功能描述:電容觸摸傳感器 RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| MAX1441IUP+T | 功能描述:電容觸摸傳感器 RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| MAX1444EHJ | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1444EHJ/V+ | 功能描述:模數轉換器 - ADC ANALOG TO DIGITAL CONVERTER RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1444EHJ/V+T | 功能描述:模數轉換器 - ADC 10-Bit 40Msps 3.0V Low-Power ADC with Internal Reference RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。