參數資料
型號: MC68HC05LJ5P
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP16
封裝: PLASTIC, DIP-16
文件頁數: 6/81頁
文件大小: 905K
代理商: MC68HC05LJ5P
GENERAL RELEASE SPECIFICATION
November 10, 1998
MOTOROLA
GENERAL DESCRIPTION
MC68HC05LJ5
1-4
REV 1
1.5
FUNCTIONAL PIN DESCRIPTION
The following paragraphs give a description of the general function of each pin
assigned in Figure 1-2 and Figure 1-3.
1.5.1 VDD AND VSS
Power is supplied to the MCU through VDD and VSS. VDD is the positive supply,
and VSS is ground. The MCU operates from a single power supply.
Very fast signal transitions occur on the MCU pins. The short rise and fall times
place very high short-duration current demands on the power supply. To prevent
noise problems, special care should be taken to provide good power supply
bypassing at the MCU by using bypass capacitors with good high-frequency char-
acteristics that are positioned as close to the MCU as possible. Bypassing
requirements vary, depending on how heavily the MCU pins are loaded.
1.5.2 OSC1, OSC2/R
The OSC1 and OSC2/R pins are the connections for the on-chip oscillator. The
OSC1 and OSC2/R pins can accept the following sets of components:
1.
A crystal as shown in Figure 1-4(a)
2.
A ceramic resonator as shown in Figure 1-4(a)
3.
An external resistor as shown in Figure 1-4(b)
4.
An external clock signal as shown in Figure 1-4(c)
The frequency, fOSC, of the oscillator or external clock source is divided by two to
produce the internal operating frequency, fOP. The type of oscillator is selected by
a mask option. An internal 2M
resistor may be selected between OSC1 and
OSC2/R by a mask option (crystal/ceramic resonator mode only).
If the RC oscillator option is selected, OSC1 pin should be connected to a known
logic level, either one or zero.
Crystal Oscillator
The circuit in Figure 1-4(a) shows a typical oscillator circuit for an AT-cut, parallel
resonant crystal. The crystal manufacturer’s recommendations should be fol-
lowed, as the crystal parameters determine the external component values
required to provide maximum stability and reliable start-up. The load capacitance
values used in the oscillator circuit design should include all stray capacitances.
The crystal and components should be mounted as close as possible to the pins
for start-up stabilization and to minimize output distortion. An internal start-up
resistor of approximately 2 M
is provided between OSC1 and OSC2/R for the
crystal type oscillator as a mask option.
相關PDF資料
PDF描述
MC68HC05M4CFN 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC52
MC68HC05M4MFN 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC52
MC68HC05P1ADWR2 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28
MC68HSC05P1ADWR2 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO28
MC68HCL05P1ADWR2 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28
相關代理商/技術參數
參數描述
MC68HC05M6 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:microcomputer unit with VFD drive capacity
MC68HC05M9 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:microcomputer unit with VFD drive capability
MC68HC05P1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit
MC68HC05P15 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:SPECIFICATION
MC68HC05P18 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Advance Information