參數資料
型號: MC68MH360ZQ33L
廠商: Freescale Semiconductor
文件頁數: 10/158頁
文件大小: 0K
描述: IC MPU QUICC 33MHZ 357-PBGA
標準包裝: 44
系列: M683xx
處理器類型: M683xx 32-位
速度: 33MHz
電壓: 5V
安裝類型: 表面貼裝
封裝/外殼: 357-BBGA
供應商設備封裝: 357-PBGA(25x25)
包裝: 托盤
Chapter 6. QMC Initialization
6.3 Restarting the Transmitter
A global underrun may require the SCC transmitter to be restarted. However, for channel-
specic errors, only the affected channel need be restarted. The following steps are required
to restart each channel:
Prepare buffer descriptors.
Set the POL bit in the channel mode register.
A stopped, but not deactivated channel is started as described above. A deactivated channel
must rst have the ZISTATE and TSTATE reinitialized to their correct values, followed by
setting TSATTx[V] and CHAMR[ENT]. Lastly, set CHAMR[POL] if the buffers are ready.
6.4 Restarting the Receiver
A global receiver overrun may require the SCC receiver to be restarted. However, for
channel-specic errors, only the affected channel need be restarted. The following steps are
required to restart each channel:
Prepare buffer descriptors.
Initialize the ZDSTATE to either 0x080 (HDLC) or 0x1800_0080 (transparent).
Initialize the RSTATE to 0x3900_0000 for MH360 and 860MH.
6.5 Disabling Receiver and Transmitter
A transmit channel can be stopped from sending any more data to the line with the STOP
command described in Section 3.1, “Transmit Commands.” The transmitter will continue
to send IDLEs or FLAGs according to the channel mode register setting. To deactivate a
channel, the V bit has to be cleared in the time slot assignment table and the ENT bit has to
be cleared in the channel mode register.
To stop a channel while receiving, use the STOP command as described in Section 3.2,
“Receive Commands,” then perform a restart as described above.
6.6 Debugging Hints
Note that the following guidelines are subject to change; code should not rely on this
information. The hints are for debugging purposes only.
6.6.1 Pointer Registers
Table 6-7 discusses the debugging hints for pointer registers. See Section 2.4.1, “Channel-
Specic HDLC Parameters,” and See Section 2.4.2, “Channel-Specic Transparent
Parameters,” for more information.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
FMC43DRXH-S734 CONN EDGECARD 86POS DIP .100 SLD
FMC36DRYS-S93 CONN EDGECARD 72POS .100 DIP SLD
MC68MH360VR33L IC MPU QUICC 33MHZ 357-PBGA
FMM43DSES-S243 CONN EDGECARD 86POS .156 EYELET
FSM44DSEF-S243 CONN EDGECARD 88POS .156 EYELET
相關代理商/技術參數
參數描述
MC68MH360ZQ33LR2 功能描述:微處理器 - MPU QUICC 2SMC 1SPI RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC68P11E1CFN2R2 制造商:Rochester Electronics LLC 功能描述:8BIT MCU 512RAM A/D EE - Bulk
MC68P11E1CFNE2R 功能描述:8位微控制器 -MCU 8B MCU 512 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68P-3-2 制造商:PARKER 功能描述:
MC-68PLCC 制造商:SPC Multicomp 功能描述:SOCKET PLCC 68 PIN THRU-HOLE 制造商:SPC Multicomp 功能描述:SOCKET, PLCC, 68 PIN, THRU-HOLE 制造商:PRIVATE LABEL 功能描述:PLCC SOCKET, 68POS, THROUGH HOLE, Connector Type:PLCC Socket, Series:-, No. of C 制造商:SPC Multicomp 功能描述:PLCC SOCKET, 68POS, THROUGH HOLE, Connector Type:PLCC Socket, Series:-, No. of Contacts:68, Pitch Spacing:1.27mm, Contact Termination:Through Hole Vertical, Contact Material:Phosphor Bronze, Contact Plating:Tin , RoHS Compliant: Yes