參數資料
型號： PCT789T-A
英文描述： PCI HSP56 World MicroModem/PCT303DW/PCT1789W
中文描述： 世界MicroModem/PCT303DW/PCT1789W的PCI HSP56
文件頁數： 25/70頁
文件大?。?/td> 872K
代理商： PCT789T-A
PC-TEL, Inc.
25
1789W0DOCDAT06A-0299
PCT1789W DATA SHEET
PCT303DW F
UNCTIONAL
D
ESCRIPTION
!
PRELIMINARY
PRELIMINARY
The PCT303DW also supports an additional power-
down mode. When both the PDN (register 6, bit 3) and
PDL (register 6, bit 4) are set, the chip-set enters a
complete power-down mode and draws negligible
current. Set the PDL bit either before setting the PDN bit
or at the same time. In this mode, the RGDT pin does
not function. Normal operation may be restored using
the same process for taking the chip-set out of sleep
mode.
Analog Output
The PCT303DW supports an analog output (AOUT) for
driving the call progress speaker found with most of
today’s modems. AOUT is an analog signal that is
comprised of a mix of the transmit and receive signals.
The receive portion of this mixed signal has a 0 dB gain,
while the transmit signal has a gain of –20 dB.
The transmit and receive signals of the AOUT signal
have independent mute controls. The ATM bit (register
6, bit 6) mutes the transmit portion, while the ARM
(register 6, bit 5) mutes the receive portion. Figure 3 on
page 8 illustrates a recommended application circuit.
Note that in the configuration shown, the LM386
provides a gain of 26 dB. Additional gain adjustments
may be made by varying the voltage divider created by
R1 and R3 of Figure 3.
On-Hook Line Monitor
The PCT303DW allows the user to detect line activity
when the device is in an on-hook state. When the
system is on-hook, the line data can be passed to the
DSP across the serial port while drawing a small amount
of DC current from the line. This feature is similar to the
passing of line information (such as caller ID), while on-
hook, following a ring signal detection. To activate this
feature, set the ONHM bit in register 5.
The on-hook line monitor can also be used to detect
whether a phone line is physically connected to the
PCT303W and associated circuitry. When the on-hook
line monitor is activated (if no line is connected), the
output of SDO will move towards a negative full scale
value (–32768). The value is guaranteed to be at least
89% of negative full scale.
If a line is present while in on-hook line monitor mode,
SDO will have a near zero value. The designer must
allow for the group delay of the receive filter before
making a decision.
The on-hook line monitor may be used in conjunction
with the loop current sense bits to determine if a phone
line is physically connected to the PCT303W and
associated circuitry. When on-hook line monitor is active
(if a phone line is present), the LCS value will be a 1111b
value.
If a phone line is not present, the LCS value will be a
zero value. The designer must allow for a 5/Fs delay
before making a decision. Refer to “Loop Current
Monitor” for more details on the LCS bits.
Loop Current Monitor
When the system is in an off-hook state, the LCS bits of
register 12 indicate the approximate amount of DC loop
current that is flowing in the loop. The LCS is a 4-bit
value ranging from zero to fifteen. Each unit represents
approximately 6 mA of loop current. An LCS value of
zero means the loop current is less than required for
normal operation and the system should be on-hook. An
LCS value of 15 means the loop current is greater than
120 mA. To determine a rough approximation of the
current (mA) flowing in the loop the following equation
may be used:
The LCS detector has a built-in hysteresis of 2 mA of
current. This allows for a stable LCS value when the
loop current is near a transition level. The LCS value is
a rough approximation of the loop current, and the
designer is advised to use this value in a relative means
rather than an absolute value.
This feature enables the modem to determine if an
additional line has “picked up” while the modem is
transferring information. In the case of a second phone
going off-hook, the loop current falls approximately 50%
and is reflected in the value of the LCS bits.
Gain Control
The PCT303DW supports multiple gain and attenuation
settings for the receive and transmit paths, respectively.
When the ARX bit is set, 6 dB of gain is applied to the
receive path. When the ATX bit is set, –3 dB of gain is
applied to the transmit path.
Register 15 can be used to provide additional gain
control. For register 15 to have an effect on the receive
and transmit paths, the ATX and ARX bits of register 13
must be zero.
The receive path can support gains of 0, 3, 6, 9, and 12
dB. The gain is selected by bits 2:0 (ARX2:ARX0). The
receive path can also be muted by setting bit 3 (RXM).
The transmit path can support attenuations of 0, 3, 6, 9,
and 12 dB. The attenuation is selected by bits 6:4
(ATX2:ATX0). The transmit path can also be muted by
setting bit 7 (TXM).
LoopCurrent
6
LCS
12
+
≈
相關PDF資料
PDF描述
PCX-150 150A QUASI- CW LASER DIODE DRIVER/PULSED CURRENT SOURCE
PCX-6220 150A 40V QUASI-CW LASER DIODE DRIVER/PULSED CURRENT SOURCE
PCXO116 Logic IC
PD-110A CAP,CERM,TRIM,5mm,9-50pf, 200VDC COLOR GREEN,2 LEADS
PD-110B CAP,CERM,TRIM,8mm,8.5-100pF, 250V,COLOR PURPLE
相關代理商/技術參數
參數描述
PCT789T-C 制造商:PCTEL 功能描述:PCI MODEM CHIP
PCT789T-C1 制造商:Rochester Electronics LLC 功能描述:- Bulk
PCT900 制造商:General Tools 功能描述:Combination Contact/Non-Contact Laser Tachometer 制造商:General Tools 功能描述:TACHOMETERMINI PHOTO
PCT-A 制造商:Cooper Interconnect 功能描述: 制造商:Cooper Bussmann 功能描述: 制造商:COOPER BUSSMANN 功能描述:Fuse Holder 125V Pin Through Hole
PCTABLE 制造商:Black Box Corporation 功能描述:PC / UTILITY TABLE 28"H X 36"W X 24"D
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*