- 您現在的位置：買賣IC網 > PDF目錄369953 > PCT789T-A PCI HSP56 World MicroModem/PCT303DW/PCT1789W PDF資料下載
參數資料
| 型號： | PCT789T-A |
| 英文描述： | PCI HSP56 World MicroModem/PCT303DW/PCT1789W |
| 中文描述： | 世界MicroModem/PCT303DW/PCT1789W的PCI HSP56 |
| 文件頁數： | 27/70頁 |
| 文件大?。?/td> | 872K |
| 代理商： | PCT789T-A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
PC-TEL, Inc.
27
1789W0DOCDAT06A-0299
PCT1789W DATA SHEET
PCT303DW F
UNCTIONAL
D
ESCRIPTION
!
PRELIMINARY
PRELIMINARY
Exception Handling
The PCT303DW provides several mechanisms to
determine if an error occurs during operation. Through
the secondary frames of the serial link, the controlling
DSP can read several status bits. The bit of highest
importance is the frame detect bit (FDT, register 12 bit
6). This bit indicates that the DSP side (PCT303D) and
line side (PCT303W) devices are communicating.
During normal operation, the FDT bit can be checked
before reading any bits that indicate information about
the line side. If FDT is not set, the following bits related
to the line side are invalid—RDT, LCS, CBID, REVB; the
RGDT operation will also be non-functional.
Following power-up and reset, the FDT bit is not set
because the PDL bit (register 6 bit 4) defaults to 1. In this
state, the ISOLink is not operating and no information
about the line side can be determined. The user must
program the clock generator to a valid configuration for
the system and clear the PDL bit to activate the ISOLink.
While the DSP and line side are establishing
communication, the DSP side does not generate
FSYNC signals. Therefore, if the controlling DSP serial
interface is interrupt driven, based on the FSYNC signal,
the controlling DSP does not require a special delay
loop to wait for this event to complete.
The FDT bit can also indicate if the line side executes an
off-hook request successfully. If the line side is not
connected to a phone line (that is, the user fails to
connect a phone line to the modem), the FDT bit
remains cleared. The controlling DSP must allow
sufficient time for the line side to execute the off-hook
request. The maximum time for FDT to be valid following
an off-hook request is 10 ms. If the FDT is high, the LCS
bits indicate the amount of loop current flowing. If the
FDT fails to be set following an off-hook request, the
PDL bit in register 6 must be set high for at least 1 ms to
reset the line side. For more information, see “Loop
Current Monitor” on page 25.
Another useful bit is the communication link error (CLE)
bit (register 12 bit 7). The CLE bit indicates a time-out
error for the ISOLink following a change to either PLL1
or PLL2. For more information, see “Clock Generation
Subsystem” on page 22. When the CLE bit is set, the
DSP side chip has failed to receive verification from the
line side that the clock change has been accepted in an
expected period of time. This condition indicates a
severe error in programming the clock generator or
possibly a defective line-side chip.
相關PDF資料 |
PDF描述 |
|---|---|
| PCX-150 | 150A QUASI- CW LASER DIODE DRIVER/PULSED CURRENT SOURCE |
| PCX-6220 | 150A 40V QUASI-CW LASER DIODE DRIVER/PULSED CURRENT SOURCE |
| PCXO116 | Logic IC |
| PD-110A | CAP,CERM,TRIM,5mm,9-50pf, 200VDC COLOR GREEN,2 LEADS |
| PD-110B | CAP,CERM,TRIM,8mm,8.5-100pF, 250V,COLOR PURPLE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCT789T-C | 制造商:PCTEL 功能描述:PCI MODEM CHIP |
| PCT789T-C1 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| PCT900 | 制造商:General Tools 功能描述:Combination Contact/Non-Contact Laser Tachometer 制造商:General Tools 功能描述:TACHOMETERMINI PHOTO |
| PCT-A | 制造商:Cooper Interconnect 功能描述: 制造商:Cooper Bussmann 功能描述: 制造商:COOPER BUSSMANN 功能描述:Fuse Holder 125V Pin Through Hole |
| PCTABLE | 制造商:Black Box Corporation 功能描述:PC / UTILITY TABLE 28"H X 36"W X 24"D |
發布緊急采購，3分鐘左右您將得到回復。