- 您現在的位置：買賣IC網 > PDF目錄379352 > SC16IS741IPW (NXP SEMICONDUCTORS) Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support PDF資料下載
參數資料
| 型號： | SC16IS741IPW |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support |
| 中文描述： | 1 CHANNEL(S), 5M bps, I2C BUS CONTROLLER, PDSO16 |
| 封裝： | 4.40 MM, PLASTIC, MO-153, SOT403-1, TSSOP-16 |
| 文件頁數： | 30/52頁 |
| 文件大?。?/td> | 382K |
| 代理商： | SC16IS741IPW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
SC16IS741_1
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 01 — 29 April 2010
30 of 52
NXP Semiconductors
SC16IS741
Single UART with I
2
C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
9.
RS-485 features
9.1 Auto RS-485 RTS control
Normally the RTS pin is controlled by MCR bit 1, or if hardware flow control is enabled, the
logic state of the RTS pin is controlled by the hardware flow control circuitry. EFCR
register bit 4 will take the precedence over the other two modes; once this bit is set, the
transmitter will control the state of the RTS pin. The transmitter automatically asserts the
RTS pin (logic 0) once the host writes data to the transmit FIFO, and deasserts RTS pin
(logic 1) once the last bit of the data has been transmitted.
To use the auto RS-485 RTS mode the software would have to disable the hardware flow
control function.
9.2 RS-485 RTS output inversion
EFCR bit 5 reverses the polarity of the RTS pin if the UART is in auto RS-485 RTS mode.
When the transmitter has data to be sent it will deasserts the RTS pin (logic 1), and when
the last bit of the data has been sent out the transmitter asserts the RTS pin (logic 0).
9.3 Auto RS-485
EFCR bit 0 is used to enable the RS-485 mode (multidrop or 9-bit mode). In this mode of
operation, a ‘master’ station transmits an address character followed by data characters
for the addressed ‘slave’ stations. The slave stations examine the received data and
interrupt the controller if the received character is an address character (parity bit = 1).
To use the auto RS-485 mode the software would have to disable the hardware and
software flow control functions.
9.3.1
Normal multidrop mode
The 9-bit Mode in EFCR (bit 0) is enabled, but not Special Character Detect (EFR bit 5).
The receiver is set to Force Parity 0 (LCR[5:3] = 111) in order to detect address bytes.
With the receiver initially disabled, it ignores all the data bytes (parity bit = 0) until an
address byte is received (parity bit = 1). This address byte will cause the UART to set the
parity error. The UART will generate a line status interrupt (IER bit 2 must be set to ‘1’ at
this time), and at the same time puts this address byte in the RX FIFO. After the controller
examines the byte it must make a decision whether or not to enable the receiver; it should
enable the receiver if the address byte addresses its ID address, and must not enable the
receiver if the address byte does not address its ID address.
If the controller enables the receiver, the receiver will receive the subsequent data until
being disabled by the controller after the controller has received a complete message
from the ‘master’ station. If the controller does not disable the receiver after receiving a
message from the ‘master’ station, the receiver will generate a parity error upon receiving
another address byte. The controller then determines if the address byte addresses its ID
address, if it is not, the controller then can disable the receiver. If the address byte
addresses the ‘slave’ ID address, the controller take no further action, the receiver will
receive the subsequent data.
相關PDF資料 |
PDF描述 |
|---|---|
| SC16IS752IBS | Dual UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support |
| SC16IS752IPW | Dual UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support |
| SC16IS762IBS | Dual UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support |
| SC16IS762IPW | Dual UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support |
| SC5R5153Z | 2.7V/2.0F Primary or back-up power supply for video, audio |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16IS741IPW,112 | 功能描述:UART 接口集成電路 IC UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16IS741IPW,118 | 功能描述:UART 接口集成電路 SINGLE UART W/ 12C-BUS/SPI INTERFC RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16IS741IPW,128 | 功能描述:UART 接口集成電路 IC UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16IS74Q900 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs |
| SC16IS750 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support |
發布緊急采購，3分鐘左右您將得到回復。