參數資料
型號： T7507
元件分類： Codec
英文描述： T7507 Quad PCM Codec with Filters, Termination Impedance, and Hybrid Balance
中文描述： T7507四路PCM編解碼器與過濾器，終端阻抗，以及混合平衡
文件頁數： 9/30頁
文件大?。?/td> 558K
代理商： T7507
Lucent Technologies Inc.
9
Data Sheet
August 1999
Termination Impedance, and Hybrid Balance
T7507 Quad PCM Codec with Filters,
Functional Description
(continued)
Microprocessor Serial Data Control and
L8567 SLIC/L7583 Switch (or EMR) Control
Interfaces
(continued)
The serial data interface has pins for data in (DI), data
out (DO), chip select (CSEL), and control clock
(CCLK). Data is read by the microcontroller from the
output shift register at the T7507 DO lead. The T7507
reads data from the microcontroller into the data input
shift register at the DI lead. The loop status latch stores
updated supervision information from the SLIC and
switch until it is transferred to the DO shift register.
On the falling edge of CSEL, the first bit of DO output
data becomes valid and ready for transmission in the
time specified by tCSLCCL. On the next falling CCLK
edge, the microprocessor will read the first bit of valid
data from the T7507 DO output. Also, on this first falling
CCLK edge, the T7507 will read the first bit of control
information on the DI input from the microcontroller.
Thus, upon the falling CSEL edge, the microcontroller
must have valid data ready at its data out lead in a time
specified by tCIVCCL.
On the next seven falling CCLK edges, the remaining
seven status bits are read by the microcontroller at the
T7507 DO lead and the remaining 7 control input bits
are read by the T7507 at the DI lead from the micro-
controller.
During the time tCCLCSH, which is the period after the
eight falling CCLK edges, the data at the DI register is
applied to the T7507 codec and made available to the
L8567 SLIC and L7583 switch input data latches. Data
is applied only if CSEL is low and has remained low on
the eighth negative edge of CCLK.
Upon the falling edge of CSEL, DO data is passed from
the loop status latch to the DO shift register. During the
period when CSEL is low, DO status data will not be
passed from the loop status latch to the DO shift regis-
ter. Consecutive read/write periods are not allowed.
CSEL must remain high for a specified time, tCSHCSL,
before CSEL can transition low again.
During CSEL low interval, the T7507 generates an EN
pulse low for one of the four channels served by the
particular T7507. These EN pulses are generated
sequentially. Thus, if EN0 is generated on a given
CSEL low, EN1 will be generated during the next CSEL
low, etc. Only one of the four EN outputs associated
with a given T7507 codec will be low during a given
CSEL interval.
Enable Transfers when CCLK Is Bursted with
CSEL
When EN is low, status information from the SLIC and
switch is updated in the T7507 8-bit loop status latch.
This data will be transferred into the data out shift regis-
ter and shifted out to the microcontroller on the next
CSEL cycle. Thus, to make a write from the L8567
SLIC or L7583 switch, it takes two CSEL cycles: the
first to create an EN pulse for a given channel and to
shift updated status information to the 8-bit status latch,
and the second CSEL cycle to shift the updated chan-
nel information to the microcontroller. Each time the
CSEL goes low and status information is shifted to the
microcontroller, only one of the four channels has new
status data; the other channels are shifting out status
data that has previously been presented to the micro-
controller. Thus, it takes five CSEL cycles to a T7507
device to ensure that supervision data for each of the
four channels associated with the T7507 device has
been updated.
When EN goes low, updated control information is also
fed to the SLIC and switch from the T7507. Since EN
for each channel is generated sequentially during suc-
cessive CSEL, four CSELs to a given T7507 device are
required to ensure that updated control information is
given to each of the four channels.
Note that to apply ringing, before the ring relay is acti-
vated to apply power ringing to the subscriber loop, the
L8567 SLIC must first be changed from the low-power
scan mode to the active mode. This is because the ring
trip detector is not active when the L8567 SLIC is in the
low-power scan mode. Thus, application of ringing to a
given channel may require as many as eight CSEL
cycles to the T7507 associated with the channel.
Enable Transfers when CCLK Is Not
Restricted to CSEL Low
The T7507 will continue to generate EN pulses
sequentially, free-running with CCLK falling edges,
when CSEL is not applied low. Thus, if there are long
periods of time when CSEL low is not presented to a
given T7507 device, enable pulse low will be generated
sequentially during this time. This feature allows for the
most recent SLIC and switch status information to be
maintained in the 8-bit loop status latch during long
periods of time when CSEL to a given T7507 device is
maintained high.
相關PDF資料
PDF描述
T7570 T7570 Programmable PCM Codec with Hybrid-Balance Filter
T7630 T7630 Dual T1/E1 5.0 V Short-Haul Terminator (Terminator-II)
T7630 Dual T1/E1 5.0 V Short-Haul Terminator (Terminator-II)(雙 T1/E1 5.0V短距離通信終端器)
T8100A H.100/H.110 Interface and Time-Slot Interchangers
T8102A H.100/H.110 Interface and Time-Slot Interchangers
相關代理商/技術參數
參數描述
T75-08M2 制造商:The Cherry Corporation 功能描述:
T-751 制造商:RHOMBUS-IND 制造商全稱:Rhombus Industries Inc. 功能描述:Fly Back Transformer
T75-24C3 制造商:Stancor 功能描述:Power Transformer Triple Prim. Single Sec. 120V/208V/240V Prim. 24V Sec. Flange Mount
T7570 制造商:AGERE 制造商全稱:AGERE 功能描述:T7570 Programmable PCM Codec with Hybrid-Balance Filter
T-758 制造商:RHOMBUS-IND 制造商全稱:Rhombus Industries Inc. 功能描述:Transformer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*