參數資料
型號: TPS650732TRSLRQ1
廠商: TEXAS INSTRUMENTS INC
元件分類: 電源管理
英文描述: POWER SUPPLY SUPPORT CKT, PQCC48
封裝: 6 X 6 MM, 0.4 MM PITCH, GREEN, PLASTIC, QFN-48
文件頁數: 19/90頁
文件大?。?/td> 1375K
代理商: TPS650732TRSLRQ1
VBAT(REG)
IO(CHG)
VLOWV
I(TERM)
PRECHARGE
CCFASTCHARGE
CVTAPER
DONE
Battery
Voltage
BatteryCurrent
TERMCURRENT=1
I(PRECHG)
SLVSAP7 – JANUARY 2011
www.ti.com
Figure 27. Battery Charge
In the pre-charge phase, the battery is charged at a current of IPRECHG. The battery voltage starts rising. Once the
battery voltage crosses the VLOWV threshold, the battery is charged at a current of ICHG. The battery voltage
continues to rise. When the battery voltage reaches VBAT(REG), the battery is held at a constant value of VBAT(REG).
The battery current now decreases as the battery approaches full charge. When the battery current reaches
ITERM, the TERM CURRENT flag in register CHGCONFIG0 indicates charging done by going high.
Note that termination detection is disabled whenever the charge rate is reduced from the set point because of the
actions of the thermal loop, the DPM loop or the VIN-LOW loop.
The value of the fast-charge current is set by the resistor connected from the ISET pin to GND, and is given by
the equation
ICHG = KISET / RISET
(1)
RISET = KISET / ICHG
(2)
Note that if ICHG is programmed as greater than the input current limit, the battery will not charge at the rate of
ICHG, but at the slower rate of IIN-MAX (minus the load current on the OUT pin, if any). In this case, the charger
timers will be slowed down by 2x whenever the thermal loop or DPPM is active.
I-PRECHARGE:
The value for the pre-charge current is fixed to a factor of 0.1 of the fast charge current (full scale current)
programmed by the external resistor Rset
ITERM:
The value for the termination current threshold can be set in register CHGCONFIG3 using Bits TERMINATION
CURRENT FACTOR 0 and TERMINATION CURRENT FACTOR 1. The termination current is pre-set to a factor
of 0.1 of the fast charge current programmed by the external resistor Rset.
Battery Detection and Recharge:
Whenever the battery voltage falls below VRCH (Vset-100mV), a check is performed to see whether the battery
has been removed: current IBAT(DET) is pulled from the battery for a duration tDET. If the voltage on the BAT pin
remains above VLOWV, it indicates that the battery is still connected. If the charger is enabled by Bit CHARGER
ENABLE in register CHGCONFIG1 set to 1, the charger is turned on again to top up the battery.
26
Copyright 2011, Texas Instruments Incorporated
相關PDF資料
PDF描述
TPS65110RGEG3 SWITCHED CAPACITOR REGULATOR, 520 kHz SWITCHING FREQ-MAX, PQCC24
TPS65130RGER 0.9 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC24
TPS65130RGET 0.9 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC24
TPS65131RGETG4 2.2 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC24
TPS65130RGE 0.9 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC24
相關代理商/技術參數
參數描述
TPS65073EVM-430 功能描述:電源管理IC開發工具 TPS65073 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
TPS65073RSLR 功能描述:PMIC 解決方案 5Ch Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel
TPS65073RSLT 功能描述:PMIC 解決方案 5Ch Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel
TPS650830EVM-095 功能描述:TPS650830 - Power Management, Special Purpose: Mobiles Evaluation Board 制造商:texas instruments 系列:- 零件狀態:有效 主要用途:電源管理,專用型: 手機 嵌入式:- 使用的 IC/零件:TPS650830 主要屬性:- 輔助屬性:圖形用戶接口,I2C 接口 所含物品:板 標準包裝:1
TPS650830ZAJT 功能描述:- Converter, Mobile PCs Voltage Regulator IC 8 Output 168-NFBGA (7x7) 制造商:texas instruments 系列:- 包裝:剪切帶(CT) 零件狀態:有效 應用:轉換器,移動式個人電腦 電壓 - 輸入:5.4 V ~ 24 V 輸出數:8 電壓 - 輸出:多重 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:168-TFBGA 供應商器件封裝:168-NFBGA(7x7) 標準包裝:1