參數資料
型號： XE8807AMI026TLF
廠商： Semtech
文件頁數： 138/143頁
文件大?。?/td> 0K
描述： IC MCU LOW PWR MTP FLASH 32-TQFP
標準包裝： 1
系列： XE880x
應用： 感測機
核心處理器： Coolrisc816?
程序存儲器類型： 閃存（11 kB）
控制器系列： XE8000
RAM 容量： 512 x 8
接口： UART，USRT
輸入/輸出數： 24
電源電壓： 2.4 V ~ 5.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 32-TQFP
包裝： 標準包裝
供應商設備封裝： 32-TQFP（7x7）
產品目錄頁面： 585 (CN2011-ZH PDF)
配用： XE8000MP-ND - PROG BOARD AND PROSTART2 CARD
其它名稱： XE8807AMI026DKR
Semtech 2006
www.semtech.com
14-14
XE8806A/XE8807A
RfifBRCoarse[1:0]
coarse
00
1
01
4
10
8
11
16
Table 14-18 : Effect of RfifBRCoarse[1:0]
Even if the external bit synchronizer is used, the baud rate should be set correctly.
14.11 Specifications
If a frequency difference exists between the transmitter and the receiver, the receiver may be unable to decode the
received messages correctly. This is especially the case if no protocol or if the NRZ protocols are used without an
external bit synchronization clock since these signals do not contain clock information. Manchester and Miller
coding are more robust since the decoder can resynchronize on the code itself.
The estimated maximal tolerated frequency difference between the transmitter and the RF interface are the
following (theoretical values):
Mode
Maximal tolerated
f=f
RX-fTX
NRZ, no external clock
to receive 10 identical
and consecutive bits:
±4%
NRZ, with external clock
-50%/+100%
Manchester
-17%/+11%
Miller
-9%/+8%
Table 14-19 : Frequency difference tolerance
In NRZ without external bit synchronizer, it should be noted that the tolerated frequency deviation is larger if the
number of consecutive identical bits is lower than 10.
14.12 Application hints
Standard API functions to drive the XE1200 series are given in the TN8000.18. Using these API functions will allow
you to set-up a transmission between two systems very quickly.
Below, you will find some examples on how to set-up the RF circuits and the RF interface (BitJockey
TM).
14.12.1
Using the RF interface with the XE1201A
This chapter gives some examples on how the RF interface can be used with the XE1201A circuit. It does not
describe all possibilities but selects some representative cases.
14.12.1.1 Microcontroller – transceiver connections
For the external components required to operate the XE1201A, please refer to the XE1201A datasheet.
The connections between the XE8000 microcontroller and the XE1201A are shown in Figure 14-8. The
transmission data pins are connected between the RF interface of the microcontroller and the transceiver. The
configuration lines of the XE1201A can be driven by pins of a parallel port. The 3-wire configuration data bus of the
XE1201A is used to set-up the circuit by writing in the registers A, B and C. The interface can be driven by a
hardware SPI or by a software SPI on a parallel port. Pins of the RF interface RFIF0 to RFIF3 that are not used
may remain floating.
相關PDF資料
PDF描述
XIO2200AGGW IC PCI-EXPRESS/BUS BRIDGE 176BGA
XIO2200AZGW IC PCI-EXPRESS/BUS BRIDGE 176BGA
XPC823ZT81B2T IC MPU POWERQUICC 81MHZ 256-PBGA
XPC8240RZU250E MCU HOST PROCESSOR 352-TBGA
XQ6SLX150T-3CSG484I IC FPGA SPARTAN-6Q 484-CSBGA
相關代理商/技術參數
參數描述
XE88LC01 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Sensing Machine 16 + 10 bit Data Acquisition Ultra Low-Power Microcontroller
XE88LC01MI000 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Sensing Machine 16 + 10 bit Data Acquisition Ultra Low-Power Microcontroller
XE88LC01MI027 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Sensing Machine 16 + 10 bit Data Acquisition Ultra Low-Power Microcontroller
XE88LC01MI032 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Sensing Machine 16 + 10 bit Data Acquisition Ultra Low-Power Microcontroller
XE88LC01RI000 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Sensing Machine 16 + 10 bit Data Acquisition Ultra Low-Power Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*