參數資料
型號： XRT73L02
廠商： Exar Corporation
英文描述： 2 Channel E3/DS3/STS-1 Line Interface Unit(2通道 E3/DS3/STS-1線接口單元)
中文描述： 2頻道E3/DS3/STS-1線路接口單元（2通道E3/DS3/STS-1線接口單元）
文件頁數： 59/62頁
文件大?。?/td> 716K
代理商： XRT73L02
á
XRT73L02
2 CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
PRELIMINARY
REV. P1.1.0
55
A4 and A5 must be set to "0" as shown in Figure 31.
Bit 8 - A6:
The value of "A6" is a don't care.
Once these first 8 bits have been written into the Mi-
croprocessor Serial Interface, the subsequent action
depends upon whether the current operation is a
Read or Write operation.
Read Operation
Once the last address bit (A3) has been clocked into
the SDI input, the Read operation proceeds through
an idle period lasting three SClk periods. On the fall-
ing edge of SClk Cycle #8 (see Figure 31) the serial
data output signal (SDO) becomes active. At this
point, reading the data contents of the addressed
Command Register at Address [A3, A2, A1, A0] via
the SDO output pin can begin. The Microprocessor
Serial Interface outputs this five bit data word (D0
through D4) in ascending order with the LSB first, on
the falling edges of the SClk pin. Consequently, the
data on the SDO output pin is sufficiently stable for
reading by the Microprocessor on the very next rising
edge of the SClk pin.
Write Operation
Once the last address bit (A3) has been clocked into
the SDI input, the Write operation proceeds through
an idle period lasting three SClk periods. Prior to the
rising edge of SClk Cycle # 9 (see Figure 31). Apply
the desired eight bit data word to the SDI input pin via
the Microprocessor Serial Interface. The Micropro-
cessor Serial Interface latches the value on the SDI
input pin on the rising edge of SClk. Apply this word
(D0 through D7) serially, in ascending order with the
LSB first.
Simplified Interface Option
The design of the circuitry connecting to the Micro-
processor Serial Interface can be simplified by tying
both the SDO and SDI pins together and reading data
from and/or writing data to this combined signal. This
simplification is possible because only one of these
signals are active at any given time. The inactive sig-
nal is tri-stated.
N
OTES
:
1. A4 and A5 is always "0"
2. R/W = "1" for "Read" Operations
3. R/W = "0" for "Write" Operations
4. Shaded blocks denotes a "don't care" value
F
IGURE
31. M
ICROPROCESSOR
S
ERIAL
I
NTERFACE
D
ATA
S
TRUCTURE
D0
D1
D2
0
0
0
D4
D3
High Z
SDO
A0
D0
R/W
D1
A6
0
0
A3
A2
A1
D7
D6
D5
D4
D3
D2
SDI
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SClk
CS
High Z
相關PDF資料
PDF描述
XRT73L03A 3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73L03AIV 3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73L03B 3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73L03BIV 3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73L04A 4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
相關代理商/技術參數
參數描述
XRT73L02M 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73L02MES 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT73L02MIV 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73L02MIV-F 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73L02MIVTR-F 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*