參數資料
型號： XRT75VL00IV
廠商： EXAR CORP
元件分類： 數字傳輸電路
英文描述： E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
中文描述： DATACOM, PCM TRANSCEIVER, PQFP52
封裝： 10 X 10 MM, TQFP-52
文件頁數： 30/50頁
文件大?。?/td> 268K
代理商： XRT75VL00IV
XRT75VL00
E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
REV. 1.0.3
28
5.0
This section describes the detailed operation of the various blocks in the receiver. The receiver recovers the
TTL/CMOS level data from the incoming bipolar B3ZS or HDB3 encoded input pulses.
THE RECEIVER SECTION:
5.1
The Adaptive Gain Control circuit amplifies the incoming analog signal and compensates for the various flat
losses and also for the loss at one-half symbol rate. The AGC has a dynamic range of 30 dB.
The Equalizer restores the integrity of the signal and compensates for the frequency dependent attenuation of
up to 900 feet of coaxial cable (1300 feet for E3). The Equalizer also boosts the high frequency content of the
signal to reduce the Inter-Symbol Interference (ISI) so that, the slicer slices the signal at 50% of peak voltage to
generate Positive and Negative data.
The Equalizer can either be “IN” or “OUT” by setting the REQEN pin “High” or “Low” (in Hardware Mode) or
setting the REQEN control bit to “1” or “0” (in Host Mode).
R
ECOMMENDATIONS
FOR
E
QUALIZER
S
ETTINGS
:
The Equalizer has two gain settings to provide optimum equalization. In the case of normally shaped DS3/
STS-1 pulses (pulses that meet the template requirements) that has been driven through 0 to 900 feet of cable,
the Equalizer can be left “IN” by setting the REQEN pin to “High” (in Hardware Mode) or setting the REQEN
control bit to “1” (in Host Mode).
However, for square-shaped pulses such as E3 or for DS3/STS-1 high pulses (that does not meet the pulse
template requirements), it is recommended that the Equalizer be left “OUT” for cable length less than 300 feet
by setting the REQEN pin “Low” (in Hardware Mode) or by setting the REQEN control bit to “0” (in Host
Mode).This would help to prevent over-equalization of the signal and thus optimize the performance in terms of
better jitter transfer characteristics.
N
OTE
:
The results of extensive testing indicates that even when the Equalizer was left “IN” (REQEN = “HIGH”), regardless
of the cable length, the integrity of the E3 signal was restored properly over 0 to 12 dB cable loss at Industrial
Temperature.
The Equalizer also contain an additional 20 dB gain stage to provide the line monitoring capability of the
resistively attenuated signals which may have 20dB flat loss. This capability can be turned on by writing a “1” to
the RxMON bits in the control register or by setting the RxMON pin (pin 27) “High”.
5.1.1
Interference Tolerance:
For E3 mode, ITU-T G.703 Recommendation specifies that the receiver be able to recover error-free clock and
data in the presence of a sinusoidal interfering tone signal. For DS3 and STS-1 modes, the same
AGC/Equalizer:
相關PDF資料
PDF描述
XRT79L71 1 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L71IB 1 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L72 2 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L72IB 2 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L73 3 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
相關代理商/技術參數
參數描述
XRT75VL00IV-F 功能描述:外圍驅動器與原件 - PCI 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75VL00IVTR 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75VL00IVTR-F 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT79L71 制造商:EXAR 制造商全稱:EXAR 功能描述:1-CHANNEL DS3/E3 ATM UNI/PPP/CLEAR-CHANNEL FRAMER IC -
XRT79L71_07 制造商:EXAR 制造商全稱:EXAR 功能描述:1-CHANNEL DS3/E3 ATM UNI/PPP/CLEAR-CHANNEL FRAMER IC - HARDWARE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*