- 您現在的位置：買賣IC網 > PDF目錄371388 > 24850 Parasite-Power Digital Thermometer PDF資料下載
參數資料
| 型號： | 24850 |
| 英文描述： | Parasite-Power Digital Thermometer |
| 中文描述： | Socket 754的設計和資格要求 |
| 文件頁數： | 32/40頁 |
| 文件大?。?/td> | 2405K |
| 代理商： | 24850 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Socket 754 Design and Qualification Requirements
24850 Rev. 3.07 August 2003
The Equation (2) definition of the differential impedance assumes that the driven (or signal)
conductors have the same geometrical shape
Note
: Equation (2) is only valid for non-symmetric differential lines in homogenous media.
The differential impedance should be measured for all combinations of the three-pin arrangements as
shown in Figure 6 on page 29. The pins are intentionally numbered in a specific manner as to yield
identical
[
loop
L
matrices for pin configurations (a) through (d). This is not the case for the pin
arrangement in Figure 6e on page 29.
]
and
[
]
C
7.2.1
Differential Impedance
The following procedures are required to properly test for differential impedance.
7.2.1.1
Test Procedure
Use the procedures shown in EIA-364-108 or see the equations in terms of partial loop
inductance and Maxwell capacitance matrices. If the time domain method is used in
measurement, then the signal should have rise time of 35 to 150 ps for signal amplitude to go
from 10 – 90%.
The differential transmission line impedance for three mated pins, using one pin as the
voltage/current reference.
Any frequency domain test equipment recommended in EIA-364-108 may be used to perform the
measurements.
If time domain equipment is used, it should have sufficient sampling rates to resolve the specified
frequencies.
7.2.1.2
Test Condition
Frequency or Time Domain Method
Time Domain method uses a Rise Time: 35 to 150 ps, 10 to 90%
Frequency Domain method use 500MHz and 2 GHz
The differential impedance measured for a three-pin configuration (S1, S2, G).
7.2.1.3
Requirements
The acceptable range for differential impedance is 100 ± 10%
with an additional ± 2-
measurement error.
32
Electrical Qualification Requirements
Chapter 7
相關PDF資料 |
PDF描述 |
|---|---|
| 2486 | 16-Bit 2-/4-Channel ツヒ ADC with PGA and Easy Drive Input Current Cancellation |
| 2495 | 16-Bit 8-/16-Channel ツヒ ADC with PGA, Easy Drive and I2C Interface |
| 249NQ | SCHOTTKY RECTIFIER |
| 249NQ135 | SCHOTTKY RECTIFIER |
| 249NQ135R | SCHOTTKY RECTIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 2485000 | 制造商:RITTAL 功能描述:LOCK FOR S/S,AES |
| 24-8500-310C | 功能描述:IC 與器件插座 ELEV. SCKT .3 CENTER COLLET 24 PINS RoHS:否 制造商:Molex 產品:LGA Sockets 節距:1.02 mm 排數: 位置/觸點數量:2011 觸點電鍍:Gold 安裝風格:SMD/SMT 端接類型:Solder 插座/封裝類型:LGA 2011 工作溫度范圍:- 40 C to + 100 C |
| 24-8500-610C | 功能描述:IC 與器件插座 ELEV. SCKT .3 CENTER COLLET 24 PINS RoHS:否 制造商:Molex 產品:LGA Sockets 節距:1.02 mm 排數: 位置/觸點數量:2011 觸點電鍍:Gold 安裝風格:SMD/SMT 端接類型:Solder 插座/封裝類型:LGA 2011 工作溫度范圍:- 40 C to + 100 C |
| 248-501 | 制造商:WAGO Innovative Connections 功能描述:TERMINAL BLOCK MARKER BLANK 制造商:WAGO Innovative Connections 功能描述:10 Strip Plain White Miniature WSB Quick Marking Strip 制造商:WAGO 功能描述:BLANK MARKER CARD 制造商:WAGO Innovative Connections 功能描述:TERMINAL BLOCK MARKER, BLANK; Series:-; Accessory Type:Terminal Block Marker; For Use With:Terminal Blocks; Legend:Blank (No Legend) ;RoHS Compliant: Yes 制造商:WAGO Innovative Connections 功能描述:MINIATURE WSB QUICK MARKING SYSTEM; PLAIN; FOR WIDTH 5 - 17.5 MM |
| 248-501 | 制造商:WAGO Innovative Connections 功能描述:MARKER CARD HORIZ BLANK PK100 制造商:WAGO 功能描述:MARKER CARD, HORIZ, BLANK, PK100 |
發布緊急采購，3分鐘左右您將得到回復。