- 您現在的位置：買賣IC網 > PDF目錄11670 > AD9895KBCZ (Analog Devices Inc)IC CCD SIGNAL PROC/GEN 64-CSPBGA PDF資料下載
參數資料
| 型號： | AD9895KBCZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 19/58頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CCD SIGNAL PROC/GEN 64-CSPBGA |
| 標準包裝： | 1 |
| 類型： | CCD 信號處理器，12 位 |
| 輸入類型： | 邏輯 |
| 輸出類型： | 邏輯 |
| 接口： | 3 線串口 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-VFBGA，CSPBGA |
| 供應商設備封裝： | 64-CSPBGA（9x9） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
REV. A
–26–
AD9891/AD9895
Table XIII contains the summary of the VSG Registers. The
AD9891/AD9895 has eight SG outputs, VSG1–VSG8. Each of
the outputs can be assigned to one of four programmed
sequences by using the SGSEL1–SGSEL8 Registers. Each
sequence is generated in the same manner as the individual vertical
sequences, with a programmable start polarity (SGPOL), first toggle
position (SGTOG1), and second toggle position (SGTOG2).
The active line where the VSG1–VSG8 pulses occur is program-
mable using the two SGACTLIN Registers. Additionally, any
of the VSG1–VSG8 pulses may be individually disabled by
using the SGMASK Register. The masking allows all of the differ-
ent SG sequences to be preprogrammed and the appropriate
pulses for odd or even fields can be masked.
SHUTTER TIMING CONTROL
CCD image exposure time is controlled through use of the substrate
clock signal (SUBCK), which pulses the CCD substrate to clear
out accumulated charge. The AD9891/AD9895 supports three
types of electronic shuttering: Normal Shutter Mode, High Preci-
sion Shutter Mode, and Low Speed Shutter Mode. Along with the
SUBCK pulse placement, the AD9891/AD9895 can accommo-
date different progressive and interlaced readout modes.
Additionally, the AD9891/AD9895 provides output signals to
control an external mechanical shutter, strobe (flash), and the
CCD bias for still mode readout (VSUB).
Normal Shutter Mode
Figure 30 shows the VD and SUBCK output for Normal Shut-
ter Mode. The SUBCK will pulse once per line, and the total
number of repetitions within the field is programmable. The
pulse polarity, width, and line location is programmable using
the SUBCKPOL, SUBCK1TOG1, and SUBCK1TOG2 Regis-
ters (see Table XIV). The number of SUBCK pulses per field is
programmed in the SUBCKNUM Register.
As shown in Figure 30, the SUBCK pulses will always begin
on the line after the sensor gates occur, specified by the
SGACTLINE Register (Addr x265 and Addr x266). The
SUBCKPOL, SUBCK1TOG, SUBCK2TOG, and
SUBCKNUM Registers are updated at the start of the line after
the sensor gate line. All other shutter mode registers are up-
dated with the majority of the AD9891/AD9895’s registers at
the VD/HD falling edge.
High Precision Shutter Mode
High precision shuttering is controlled in the same way as nor-
mal shuttering but requires a second set of toggle registers. In
this mode, the SUBCK still pulses once per line, but the last
SUBCK in the field will have an additional SUBCK pulse
whose location is determined by the SUBCK2TOG1 and
SUBCK2TOG2 Registers (see Figure 31). Finer resolution of
the exposure time is possible using this mode. Leaving both
SUBCK2TOG Registers set to 4095 (x3F) will disable the High
Precision Mode (default setting).
Low Speed Shutter Mode
For normal exposure times less than one field interval, the
EXPOSURE Register will be set to 0. Exposure times greater
than one field interval can be achieved by writing a value
greater than zero to the EXPOSURE Register. As shown in
Figure 32, this shutter mode will suppress the SUBCK and
VSG outputs for up to 4095 fields (VD periods). The VD and
HD outputs may be suppressed during the exposure period by
programming the VDHDOFF Register to 1.
VD
SUBCK
SUBCK PROGRAMMABLE SETTINGS:
1: PULSE POLARITY USING THE SUBCKPOL REGISTER
2: NUMBER OF PULSES WITHIN THE FIELD USING THE SUBCKNUM REGISTER
3: PIXEL LOCATION OF PULSE WITHIN THE LINE AND PULSE WIDTH PROGRAMMED USING SUBCK1 TOGGLE POSITION REGISTERS
t
EXP
VSG1–
VSG8
HD
t
EXP
Figure 30. Normal Shutter Mode
VD
SUBCK
NOTES
1. 2ND SUBCK PULSE IS ADDED IN THE LAST SUBCK LINE.
2. LOCATION OF 2ND PULSE IS FULLY PROGRAMMABLE USING THE SUBCK2 TOGGLE POSITION REGISTERS.
VSG1–
VSG8
HD
t
EXP
t
EXP
Figure 31. High Precision Shutter Mode
相關PDF資料 |
PDF描述 |
|---|---|
| AD9849AKSTZ | IC CCD SIGNAL PROC 12BIT 48LQFP |
| AD9847AKSTZ | IC CCD SIGNAL PROC 10BIT 48-LQFP |
| AD9944KCPZ | IC CCD SIGNAL PROCESSOR 32-LFCSP |
| 3-221185-1 | PLUG,75 OHM,COML BNC |
| AD9943KCPZ | IC CCD SIGNAL PROCESSOR 32-LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9895KBCZRL | 功能描述:IC CCD SIGNAL PROC/GEN 64-CSPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD9898 | 制造商:AD 制造商全稱:Analog Devices 功能描述:CCD Signal Processor with Precision Timing⑩ Generator |
| AD9898KCP-20 | 制造商:Rochester Electronics LLC 功能描述:10 BIT 20 MSPS ANALOG FRONT END CONVERTE - Bulk 制造商:Analog Devices 功能描述: |
| AD9898KCPRL-20 | 制造商:AD 制造商全稱:Analog Devices 功能描述:CCD Signal Processor with Precision Timing⑩ Generator |
| AD9899ARS-2 | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。