參數資料
型號: ADSP-21369KSWZ-5A
廠商: Analog Devices Inc
文件頁數: 5/64頁
文件大小: 0K
描述: IC DSP 32BIT 366MHZ 208LQFP
標準包裝: 1
系列: SHARC®
類型: 浮點
接口: DAI,DPI
時鐘速率: 366MHz
非易失內存: ROM(768 kB)
芯片上RAM: 256kB
電壓 - 輸入/輸出: 3.30V
電壓 - 核心: 1.20V
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 208-LQFP 裸露焊盤
供應商設備封裝: 208-LQFP-EP(28x28)
包裝: 托盤
Rev. F
|
Page 13 of 64
|
October 2013
PIN FUNCTION DESCRIPTIONS
The following symbols appear in the Type column of Table 8:
A = asynchronous, G = ground, I = input, O = output,
O/T = output three-state, P = power supply, S = synchronous,
(A/D) = active drive, (O/D) = open-drain, (pd) = pull-down
resistor, (pu) = pull-up resistor.
The ADSP-21367/ADSP-21368/ADSP-21369 SHARC proces-
sors use extensive pin multiplexing to achieve a lower pin count.
For complete information on the multiplexing scheme, see the
ADSP-21368 SHARC Processor Hardware Reference, “System
Design” chapter.
Table 8. Pin Descriptions
Name
Type
State During/
After Reset
(ID = 00x)
Description
ADDR23–0
O/T (pu)1
Pulled high/
driven low
External Address. The processors output addresses for external memory and peripher-
als on these pins.
DATA31–0
I/O (pu)1
Pulled high/
pulled high
External Data. Data pins can be multiplexed to support external memory interface data
(I/O), the PDAP (I), FLAGS (I/O), and PWM (O). After reset, all DATA pins are in EMIF mode
and FLAG(0-3) pins are in FLAGS mode (default). When configured using the IDP_P-
DAP_CTL register, IDP Channel 0 scans the external port data pins for parallel input data.
ACK
I (pu)
Memory Acknowledge. External devices can deassert ACK (low) to add wait states to an
external memory access. ACK is used by I/O devices, memory controllers, or other periph-
erals to hold off completion of an external memory access.
MS0–1
O/T (pu)1
Pulled high/
driven high
Memory Select Lines 0–1. These lines are asserted (low) as chip selects for the corre-
sponding banks of external memory. The MS3-0 lines are decoded memory address lines
that change at the same time as the other address lines. When no external memory access
is occurring, the MS3-0 lines are inactive; they are active, however, when a conditional
memory access instruction is executed, whether or not the condition is true.
The MS1 pin can be used in EPORT/FLASH boot mode. See the processor hardware
reference for more information.
RD
O/T (pu)1
Pulled high/
driven high
External Port Read Enable. RD is asserted whenever the processors read a word from
external memory.
WR
O/T (pu)1
Pulled high/
driven high
External Port Write Enable. WR is asserted when the processors write a word to external
memory.
FLAG[0]/IRQ0
I/O
FLAG[0] INPUT
FLAG0/Interrupt Request 0.
FLAG[1]/IRQ1
I/O
FLAG[1] INPUT
FLAG1/Interrupt Request 1.
FLAG[2]/IRQ2/
MS2
I/O with pro-
grammablepu
(for MS mode)
FLAG[2] INPUT
FLAG2/Interrupt Request 2/Memory Select 2.
FLAG[3]/
TMREXP/MS3
I/O with pro-
grammablepu
(for MS mode)
FLAG[3] INPUT
FLAG3/Timer Expired/Memory Select 3.
相關PDF資料
PDF描述
TAP106M035BRW CAP TANT 10UF 35V 20% RADIAL
XC2C384-10FGG324C IC CR-II CPLD 384MCELL 324-FBGA
HMM28DSAI CONN EDGECARD 56POS R/A .156 SLD
ADSP-21369KBPZ-2A IC DSP 32BIT 333MHZ 256-BGA
VE-21M-CY-F1 CONVERTER MOD DC/DC 10V 50W
相關代理商/技術參數
參數描述
ADSP-21369KSWZ-6A 功能描述:IC DSP 32BIT 400MHZ 208-LQFP 制造商:analog devices inc. 系列:SHARC? 包裝:托盤 零件狀態:有效 類型:浮點 接口:DAI,DPI 時鐘速率:400MHz 非易失性存儲器:ROM(768 kB) 片載 RAM:256KB 電壓 - I/O:3.30V 電壓 - 內核:1.20V 工作溫度:0°C ~ 70°C(TA) 安裝類型:表面貼裝 封裝/外殼:208-LQFP 裸露焊盤 供應商器件封裝:208-LQFP-EP(28x28) 標準包裝:1
ADSP-21369KSZ-1A 制造商:Analog Devices 功能描述:DSP Floating-Point 32-Bit/40-Bit 266MHz 266MIPS 208-Pin MQFP 制造商:Analog Devices 功能描述:PROCESSOR ((NS))
ADSP-21369KSZ-1A 制造商:Analog Devices 功能描述:DSP PROCESSOR ((NS))
ADSP-21371 制造商:AD 制造商全稱:Analog Devices 功能描述:SHARC Processor optimized for high performance audio processing
ADSP-21371_07 制造商:AD 制造商全稱:Analog Devices 功能描述:SHARC㈢ Processor