參數資料
型號: AM79C978
廠商: Advanced Micro Devices, Inc.
英文描述: Single-Chip 1/10 Mbps PCI Home Networking Controller
中文描述: 單芯片的1 / 10 Mbps的家庭網絡控制器的PCI
文件頁數: 35/261頁
文件大?。?/td> 3803K
代理商: AM79C978
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁
Am79C978
35
MII Management Frames
MII management frames are automatically generated
by the Am79C978 controller and conform to the MII
clause in the IEEE 802.3u standard.
The start of the frame may be a preamble of 32 ones
(unless bit 6 of register equals 1) and guarantees that
all of the external PHYs are synchronized on the same
interface. See Figure 2. Loss of synchronization is pos-
sible due to the
hot-plugging
capability of the exposed
MII.
The IEEE 802.3 specification allows you to drop the
preamble, if after reading the MII Status Register from
the external PHY you can determine that the external
PHY will support Preamble Suppression (BCR34, bit
6). After having a valid MII Status Register read, the
Am79C978 controller will then drop the creation of the
preamble stream until a reset occurs, receives a read
error, or the external PHY is disconnected.
Figure 2.
Frame Format at the MII Interface Connection
This is followed by a start field (ST) and an operation
field (OP). The operation field (OP) indicates whether
the Am79C978 controller is initiating a read or write op-
eration. This is followed by the external PHY address
(PHYAD) and the register address (REGAD) pro-
grammed in BCR33. The PHY address of 1D,1E, and
1F are reserved and should not be used. The external
PHY may have a larger address space starting at 10h
- 1Fh. This is the address range set aside by the IEEE
as vendor usable address space and will vary from
vendor to vendor. This field is followed by a bus turn-
around field. During a read operation, the bus turn-
around field is used to determine if the external PHY is
responding correctly to the read request or not. The
Am79C978 controller will tri-state the MDIO for both
MDC cycles.
During the second cycle, if the external PHY is syn-
chronized to the Am79C978 controller, the external
PHY will drive a 0. If the external PHY does not drive a
0, the Am79C978 controller will signal a MREINT
(CSR7, bit 9) interrupt, if MREINTE (CSR7, bit 8) is set
to a 1, indicating the Am79C978 controller had an MII
management frame read error and that the data in
BCR34 is not valid. The data field to/from the external
PHY is read or written into the BCR34 register. The last
field is an IDLE field that is necessary to give ample
time for drivers to turn off before the next access. The
Am79C978 controller will drive the MDC to 0 and tri-
state the MDIO anytime the MII Management Port is
not active.
To help to speed up the reading and of writing the MII
management frames to the external PHY, the MDC can
be sped up to 5 MHz by setting the FMDC bits in
BCR32. The IEEE 802.3 specification requires use of
the 2.5-MHz clock rate, but 5 MHz is also available for
the user. The 5-MHz clock rate can be used for an ex-
posed MII with one external PHY attached. The 2.5-
MHz clock rate is intended to be used when multiple
external PHYs are connected to the MII Management
Port or if compliance to the IEEE 802.3u standard is re-
quired.
Auto-Poll External PHY Status Polling
As defined in the IEEE 802.3 standard, the external
PHY attached to the Am79C978 controller
s MII has no
way of communicating important timely status informa-
tion back to Am79C978 controller. The Am79C978
controller has no way of knowing that an external PHY
has undergone a change in status without polling the
MII status register. To prevent problems from occurring
with inadequate host or software polling, the
Am79C978 controller will Auto-Poll when APEP
(BCR32, bit 11) is set to 1 to insure that the most cur-
rent information is available. See
10BASE-T PHY Man-
agement Registers
for the bit descriptions of the MII
Status Register. The contents of the latest read from
the external PHY will be stored in a shadow register in
the Auto-Poll block. The first read of the MII Status
Register will just be stored, but subsequent reads will
be compared to the contents already stored in the
shadow register. If there has been a change in the con-
tents of the MII Status Register, a MAPINT (CSR7, bit
5) interrupt will be generated on INTA if the MAPINTE
(CSR7, bit 4) is set to 1. The Auto-Poll features can be
disabled if software driver polling is required.
Preamble
1111....1111
OP
10 Rd
01 Wr
PHY
Address
Register
Address
TA
Z0 Rd
10 Wr
Data
2
Bits
5
Bits
5
Bits
2
Bits
32
Bits
ST
01
2
Bits
16
Bits
1
Bit
Idle
Z
22206B-5
相關PDF資料
PDF描述
AM79C981 Integrated Multiport Repeater Plus⑩ (IMR+⑩)
AM79C981JC Integrated Multiport Repeater Plus⑩ (IMR+⑩)
AM79C982 basic Integrated Multiport Repeater (bIMR)
AM79C982-4JC basic Integrated Multiport Repeater (bIMR)
AM79C982-8JC basic Integrated Multiport Repeater (bIMR)
相關代理商/技術參數
參數描述
AM79C978A 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller
AM79C978AKC\\W 制造商:Advanced Micro Devices 功能描述:
AM79C978AKC\W 制造商:Advanced Micro Devices 功能描述:
AM79C978AKCW 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller