- 您現在的位置：買賣IC網 > PDF目錄366551 > AM79C978 (Advanced Micro Devices, Inc.) Single-Chip 1/10 Mbps PCI Home Networking Controller PDF資料下載
參數資料
| 型號： | AM79C978 |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | Single-Chip 1/10 Mbps PCI Home Networking Controller |
| 中文描述： | 單芯片的1 / 10 Mbps的家庭網絡控制器的PCI |
| 文件頁數： | 89/261頁 |
| 文件大?。?/td> | 3803K |
| 代理商： | AM79C978 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁當前第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁
Am79C978
89
PMAT_MODE. In order to access the contents of the
PMR, PMAT_MODE bit should be programmed to 0.
When BCR45 is written to set the PMAT_MODE bit to
0, the Pattern Match logic is disabled and accesses to
the PMR are possible. Bits 6:0 of BCR45 specify the
address of the PMR word to be accessed. Writing to
BCR45 does not immediately affect the contents of the
PMR. Following the write to BCR45, the PMR word ad-
dressed by bits 6:0 of BCR45 may be read by reading
BCR45, BCR46, and BCR47 in any order. To write to
the PMR word, the write to BCR45 must be followed
by a write to BCR46 and a write to BCR47 in that order
to complete the operation. The PMR will not actually be
written until the write to BCR47 is complete.
The first two 40-bit words in this RAM serve as pointers
and contain enable bits for the eight possible match
patterns. The remainder of the RAM contains the
match patterns and associated match pattern control
bits. Byte 0 of the first word contains the pattern enable
bits. Any bit position set in this byte enables the corre-
sponding match pattern in the PMR, as an example if
the bit 3 is set, then pattern 3 is enabled for matching.
Bytes 1 to 4 in the first word are pointers to the begin-
ning of the patterns 0 to 3, and bytes 1 to 4 in the sec-
ond word are pointers to the beginning of patterns 4 to
7, respectively. Byte 0 of the second word has no func-
tion associated with it. Byte 0 of the words 2 to 63 is the
control field of the PMR. Bit 7 of this field is the End of
Packet (EOP) bit. When this bit is set, it indicates the
end of a pattern in the PMR. Bits 6-4 of the control field
byte are the SKIP bits. The value of the SKIP field indi-
cates the number of the Dwords to be skipped before
the pattern in this PMR word is compared with data
from the incoming frame. A maximum of seven Dwords
may be skipped. Bits 3-0 of the control field byte are the
MASK bits. These bits correspond to the pattern match
bytes 3-0 of the same PMR word (PMR bytes 4-1). If bit
n
of this field is 0, then byte
n
of the corresponding pat-
tern word is ignored. If this field is programmed to 3,
then bytes 0 and 1 of the pattern match field (bytes 2
and 1 of the word) are used, and bytes 3 and 2 are ig-
nored in the pattern matching operation.
The contents of the PMR are not affected by
H_RESET, S_RESET, or STOP. The contents are un-
defined after a power up reset (POR).
Magic Packet Mode
In Magic Packet mode, the controller remains fully
powered up (all VDD and VDDB pins must remain at
their supply levels). The device will not generate any
bus master transfers. No transmit operations will be ini-
tiated on the network. The device will continue to re-
ceive frames from the network, but all frames will be
automatically flushed from the receive FIFO. Slave ac-
cesses to the controller are still possible. A Magic
Packet is a frame that is addressed to the controller
and contains a data sequence anywhere in its data
field made up of 16 consecutive copies of the device
’
s
physical address (PADR[47:0]). The controller will
search incoming frames until it finds a Magic Packet
frame. It starts scanning for the sequence after pro-
cessing the length field of the frame. The data se-
quence can begin anywhere in the data field of the
frame, but must be detected before the controller
reaches the frame
’
s FCS field. Any deviation of the in-
coming frame
’
s data sequence from the required phys-
ical address sequence, even by a single bit, will
prevent the detection of that frame as a Magic Packet
frame.
The controller supports two different modes of address
detection for a Magic Packet frame. If MPPLBA (CSR5,
bit 5) or EMPPLBA (CSR116, bit 6) are at their default
value of 0, the controller will only detect a Magic Packet
frame if the destination address of the packet matches
the content of the physical address register (PADR). If
MPPLBA or EMPPLBA are set to 1, the destination ad-
dress of the Magic Packet frame can be unicast, multi-
cast, or broadcast.
Note:
The setting of MPPLBA or EMPPLBA only ef-
fects the address detection of the Magic Packet frame.
The Magic Packet
’
s data sequence must be made up
of 16 consecutive copies of the device
’
s physical ad-
dress (PADR[47:0]), regardless of what kind of destina-
tion address it has.
There are two general methods to place the controller
into Magic Packet mode. The first is the software
method. In this method, either the BIOS or other soft-
ware sets the MPMODE bit (CSR5, bit 1). Then the
controller must be put into suspend mode (see descrip-
tion of CSR5, bit 0), allowing any current network activ-
ity to finish. Finally, either PG must be deasserted
(hardware control), or MPEN (CSR5, bit 2) must be set
to 1 (software control).
Note:
FASTSPNDE (CSR7, bit 15) has no meaning in
Magic Packet mode.
The second method is the hardware method. In this
method, the MPPEN bit (CSR116, bit 4) is set at power
up by the loading of the EEPROM. This bit can also be
set by software. The controller will be placed in the
Magic Packet Mode when either the PG input is deas-
serted or the MPEN bit is set. Magic Packet mode can
be disabled at any time by asserting PG or clearing
MPEN bit.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C981 | Integrated Multiport Repeater Plus⑩ (IMR+⑩) |
| AM79C981JC | Integrated Multiport Repeater Plus⑩ (IMR+⑩) |
| AM79C982 | basic Integrated Multiport Repeater (bIMR) |
| AM79C982-4JC | basic Integrated Multiport Repeater (bIMR) |
| AM79C982-8JC | basic Integrated Multiport Repeater (bIMR) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C978A | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller |
| AM79C978AKC\\W | 制造商:Advanced Micro Devices 功能描述: |
| AM79C978AKC\W | 制造商:Advanced Micro Devices 功能描述: |
| AM79C978AKCW | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller |
發布緊急采購，3分鐘左右您將得到回復。