- 您現在的位置：買賣IC網 > PDF目錄366551 > AM79C978 (Advanced Micro Devices, Inc.) Single-Chip 1/10 Mbps PCI Home Networking Controller PDF資料下載
參數資料
| 型號： | AM79C978 |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | Single-Chip 1/10 Mbps PCI Home Networking Controller |
| 中文描述： | 單芯片的1 / 10 Mbps的家庭網絡控制器的PCI |
| 文件頁數： | 78/261頁 |
| 文件大小： | 3803K |
| 代理商： | AM79C978 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁當前第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁
78
Am79C978
Table 12.
Access ID Symbol Pulse Positions and
Encoding
The next two AID symbols (5 and 6) encode four bits of
control word information. The MSB is encoded in AID
Symbol 5. Control word messages are described fur-
ther in the
Management Interfaces
section.
AID Transmit Timing
The transmitter encodes the Access ID in a pulse posi-
tion in each 128 TIC interval. Each AID symbol interval
must have only one pulse. Pulse transmission must
start in only one of the four possible positions (mea-
sured from the beginning of the Access ID symbol) de-
fined in Table 12.
AID Receive Timing
The receiver allows for jitter by establishing a window
around each legal pulse position. This window is -2 +1
TICS wide on either side of the position. A pulse that ar-
rives outside of the legal AID positions is considered a
COLLISION event.
Collisions
A Collision is detected only during Access ID and silent
intervals (AID symbols 0 through 7). In general during
a collision, a transmitting station will read back an AID
value that does not match its own and recognizes the
event as a collision and alerts other stations with a JAM
signal. Non-transmitting stations may also detect some
collisions by interpreting received non-conforming AID
pulses as collisions.
With two transmitters colliding, each transmitter nor-
mally blanks its receive input immediately after trans-
mitting (and simultaneously receiving) a pulse.
Therefore, only when a transmitting station receives
pulses in a position earlier than the position it transmit-
ted will it recognize it as a pulse transmitted by another
station and signal a collision.
For this reason, guaranteed collision detection is pos-
sible only as long as the spacing between successive
possible pulse positions in an AID symbol (20 TICs or
2.3
μ
s) is greater than the round trip delay between the
colliding nodes. At approximately 1.5 ns propagation
delay per foot, the maximum distance between two
HomePNA units must not be greater than 500 feet for
collision detection purposes (1.5
μ
s round trip delay
plus margin).
The following criteria must be met to guarantee reliable
collision detection:
At least one HomePNA station of a colliding group
must always detect a collision when the delay between
the beginning of its transmitted packet and the begin-
ning of the received colliding packet is between -1.5
μ
s
and +1.5
μ
s.
In general, any received pulse at a HomePNA station
that does not conform to the pulse position require-
ments of AID symbols 0 through 7 shall indicate a col-
lision on the wire. When a transmitting station senses a
collision, it emits a JAM signal to alert all other stations
to the collision. The following conditions signify a COL-
LISION event:
1. A HomePNA station receives an AID that does not
match the one being sent.
2. A HomePNA station receives a pulse outside the
AID_GUARD INTERVAL in AID intervals 0 to 7.
3. A HomePNA station receives a pulse inside the
SILENT_INTERVAL (AID symbol 7).
As in all cases, pulses received during a blanking inter-
val are ignored.
Passive stations (stations not actively transmitting dur-
ing the collision) cannot reliably detect collisions.
Therefore, once a collision is detected by a transmitting
station, the station must inform the rest of the stations
of the collision with a JAM pattern described below.
Only a transmitting station emits a JAM signal.
Once a collision is detected, the COLLISION signal to
the MAC interface is asserted and is not reset until the
MAC deactivates the TXEN signal.
JAM Signal
A JAM pattern consists of 1 pulse every 32 TICs and
continues until at least the end of the AID intervals.
After the AID interval, the JAM pattern will continue
until TXEN from the MAC is deactivated.
ACCESS ID Values
The access ID values for slave stations are picked by
each individual station randomly from the set of AID
slave numbers described in the management section.
During operation, each HomePNA station monitors
HomePNA frames received on the wire. If it detects an-
other HomePNA station using the same AID, it will se-
lect a new random AID.
Silence Interval (AID symbol 7)
The Access ID symbols are followed by a fixed silence
interval of 129 TICs. The receive blanking interval is
the same as that of the AID symbols (1 through 6).
Any pulses detected in the silence interval are consid-
ered a COLLISION event for transmitting stations and
are handled as described in the
Collisions
section.
Pulse
Position
TICs from Beginning of AID
Symbol
Bit Encoding
1
66
00
2
86
01
3
106
10
4
126
11
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C981 | Integrated Multiport Repeater Plus⑩ (IMR+⑩) |
| AM79C981JC | Integrated Multiport Repeater Plus⑩ (IMR+⑩) |
| AM79C982 | basic Integrated Multiport Repeater (bIMR) |
| AM79C982-4JC | basic Integrated Multiport Repeater (bIMR) |
| AM79C982-8JC | basic Integrated Multiport Repeater (bIMR) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C978A | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller |
| AM79C978AKC\\W | 制造商:Advanced Micro Devices 功能描述: |
| AM79C978AKC\W | 制造商:Advanced Micro Devices 功能描述: |
| AM79C978AKCW | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller |
發布緊急采購，3分鐘左右您將得到回復。