參數資料
型號： AM79C978AKCW
廠商： ADVANCED MICRO DEVICES INC
元件分類： 微控制器/微處理器
英文描述： Single-Chip 1/10 Mbps PCI Home Networking Controller
中文描述： 5 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP160
封裝： PLASTIC, QFP-160
文件頁數： 109/256頁
文件大?。?/td> 3505K
代理商： AM79C978AKCW
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁當前第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁
Am79C978A
109
DWIO mode). The RDP access is a read access, and
since RAP has just been loaded with the value of 0004h,
the RDP read will yield the contents of CSR4. A read of
the BDP at this time (offset of 16h when WIO mode has
been selected, 1Ch when DWIO mode has been select-
ed) will yield the contents of BCR4, since the RAP is
used as the pointer into both BDP and RDP space.
RAP: Register Address Port
Bit
Name
Description
31-16
RES
Reserved locations. Written as
zeros and read as undefined.
15-8
RES
Reserved locations. Read and
written as zeros.
7-0
RAP
Register Address Port. The
value of these 8 bits deter-
mines which CSR or BCR will
be accessed when an I/O ac-
cess to the RDP or BDP port,
respectively, is performed.
A write access to undefined CSR
or BCR locations may cause un-
expected reprogramming of the
Am79C978A control registers. A
read access will yield undefined
values.
These bits are always read/write
accessible. RAP is cleared by
H_RESET or S_RESET and is un-
affected by setting the STOP bit.
Control and Status Registers (CSRs)
The CSR space is accessible by performing accesses
to the RDP (Register Data Port). The particular CSR
that is read or written during an RDP access will depend
upon the current setting of the RAP. RAP serves as a
pointer into the CSR space.
CSR0: Controller Status and Control Register
Certain bits in CSR0 indicate the cause of an interrupt.
The register is designed so that these indicator bits are
cleared by writing ones to those bit locations. This
means that the software can read CSR0 and write back
the value just read to clear the interrupt condition.
Bit
Name
Description
31-16
RES
Reserved locations. Written as
zeros and read as undefined.
15
ERR
Error. Error is set by the OR of
CERR, MISS, and MERR. ERR
remains set as long as any of the
error flags are true.
This bit is always read accessi-
ble only. Write operations are
ignored.
14
RES
Reserved locations. This bit is al-
ways
read/write
Read returns zero.
accessible.
13
CERR
Collision Error. Collision Error is
set by the Am79C978A controller
when the device operates in half-
duplex mode and the collision in-
puts to the GPSI port fail to acti-
vate within 20 network bit times
after the chip terminates trans-
mission (SQE Test). This feature
is a transceiver test feature.
CERR reporting is disabled when
the GPSI port is active and the
Am79C978A controller operates
in full-duplex mode.
When the MII port is selected,
CERR is only reported when the
external PHY is operating as a
half-duplex 10BASE-T PHY.
CERR assertion will not result in
an interrupt being generated.
CERR assertion will set the
ERR bit.
This bit is always read/write ac-
cessible. CERR is cleared by the
host by writing a 1. Writing a 0
has no effect. CERR is cleared
by H_RESET, S_RESET, or by
setting the STOP bit.
12
MISS
Missed Frame. Missed Frame is
set by the Am79C978A controller
when it has lost an incoming re-
ceive frame resulting from a Re-
ceive
Descriptor
available. This bit is the only im-
mediate indication that receive
data has been lost since there is
no current receive descriptor.
The Missed Frame Counter
(CSR112) also increments each
time a receive frame is missed.
not
being
When MISS is set, INTA is as-
serted if IENA is 1 and the mask
bit MISSM (CSR3, bit 12) is 0.
MISS assertion will set the ERR
bit, regardless of the settings of
IENA and MISSM.
相關PDF資料
PDF描述
AM79C978AVCW Single-Chip 1/10 Mbps PCI Home Networking Controller
AM79C978 Single-Chip 1/10 Mbps PCI Home Networking Controller
AM79C981 Integrated Multiport Repeater Plus⑩ (IMR+⑩)
AM79C981JC Integrated Multiport Repeater Plus⑩ (IMR+⑩)
AM79C982 basic Integrated Multiport Repeater (bIMR)
相關代理商/技術參數
參數描述
AM79C978AVCW 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller
AM79C978KC/W 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller
AM79C978VC/W 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller
AM79C979BKC\\W 制造商:Advanced Micro Devices 功能描述:
AM79C98 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Twisted-Pair Ethernet Transceiver (TPEX)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*