參數資料
型號: AM79C978AKCW
廠商: ADVANCED MICRO DEVICES INC
元件分類: 微控制器/微處理器
英文描述: Single-Chip 1/10 Mbps PCI Home Networking Controller
中文描述: 5 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP160
封裝: PLASTIC, QFP-160
文件頁數: 80/256頁
文件大?。?/td> 3505K
代理商: AM79C978AKCW
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁當前第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁
80
Am79C978A
Header AID Remote Control Word Commands
Stations may be configured either as master stations or
as slave stations. Only one master may exist on a given
HomePNA segment.
The master station may send commands embedded in
the HomePNA header control word to remotely set vari-
ous parameters of the remote slave stations. Stations are
identified via the AID as follows:
1. The master station is identified on the HomePNA
wire network with an AID of FFh.
2. A slave is identified with an AID of 00h to EFh.
3. AID values of F0h to FEh are reserved for future
use.
Once a command has been transmitted, the master sta-
tion will revert to a slave AID, so that subsequent control
words are not interpreted as new commands.
Master mode is entered by writing to the PHY control reg-
ister (HPR16) and is exited upon the completion of the
command sequence.
A valid master remote command consists of three Home-
PNA frames with an AID of FFh. Since the HomePNA
header is prepended to packets received from the MAC,
packets from the master station may be separated by in-
tervals during which other (slave) stations may transmit
their frames.
A remote master Control Word command must be recog-
nized and executed by a HomePNA PHY when it re-
ceives three consecutive valid HomePNA frames with an
AID of FFh.
If HPR16, bit 15 is not set to 0, valid commands are as fol-
lows:
1. SET_POWER: Commands slave stations to set
their transmit level to a prescribed level.
2. SET_SPEED: Commands slave stations to set their
transmit speed to a prescribed value.
The control word bit encoding and possible values are de-
scribed in Table 16.
Table 16.
Master Station Control Word Functions
All stations will transmit the following status messages in
the HomePNA header control word of all outgoing
frames:
1. VERSION_STATUS: The HomePNA PHY version
of the slave station.
2. POWER_STATUS: The transmit power level of the
transmitting slave station for the current frame. All
HomePNA units support LOW_POWER and
HIGH_POWER modes.
3. SPEED_STATUS: The transmit speed of the slave
station for the current frame. Receiving stations will
adjust their receiver parameters to correctly inter-
pret this frame.
The slave control word bit encoding and possible values
are described in Table 17.
Table 17.
Slave Station Control Word Status
Conditions
PHY Control and Management Block
(PCM Block)
Register Administration for 10BASE-T PHY Device
The management interface specified in Clause 22 of the
IEEE 802.3u standard provides for a simple two wire, se-
rial interface to connect a management entity and a man-
aged PHY for the purpose of controlling the PHY and
gathering status information. The two lines are Manage-
ment Data Input/Output (MDIO) and Management Data
Clock (MDC). A station management entity which is at-
tached to multiple PHY entities must have prior knowl-
edge of the appropriate PHY address for each PHY entity.
Description of the Methodology
The management interface physically transports man-
agement information across the internal MII. The informa-
tion is encapsulated in a frame format as specified in
Clause 22 of the IEEE 802.3u draft standard and is shown
in Table 18.
Bit No.
Command Function
0
0 = version 0 (All stations revert to version 0
HomePNA PHY mode of operation).
1
0 = Set transmit to low speed.
1 = Set transmit to high speed.
2
0 = Set to low power transmit mode.
1 = Set to high power transmit mode.
3
Reserved
Bit #
Indicated Status
0
0 = This station is version 0.
1 = This station is not version 0.
1
0 = Frame transmitted at low speed.
1 = Frame transmitted at high speed.
2
0 = Frame transmitted at low power.
1 = Frame transmitted at high power.
3
Reserved
相關PDF資料
PDF描述
AM79C978AVCW Single-Chip 1/10 Mbps PCI Home Networking Controller
AM79C978 Single-Chip 1/10 Mbps PCI Home Networking Controller
AM79C981 Integrated Multiport Repeater Plus⑩ (IMR+⑩)
AM79C981JC Integrated Multiport Repeater Plus⑩ (IMR+⑩)
AM79C982 basic Integrated Multiport Repeater (bIMR)
相關代理商/技術參數
參數描述
AM79C978AVCW 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller
AM79C978KC/W 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller
AM79C978VC/W 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller
AM79C979BKC\\W 制造商:Advanced Micro Devices 功能描述:
AM79C98 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Twisted-Pair Ethernet Transceiver (TPEX)